Jump to content
SAU Community

Recommended Posts

Member name

Posts

shanef

8170

Nismo_Boy

5062

Silver_R34_GT-T

4271

Bunta

3769

Ants

3170

phatboi2010

3131

Captain Natro

2779

Keegs

2658

luke GTR

2501

t5iv

2486

Col-GTSX

2425

markimak

2389

Mr-Toy33

2331

impact_blue

2273

lilmike86

1965

LIL34

1947

SMR33

1894

Konrad

1894

FineLine

1879

Oblivion

1334

85URK

1333

Squizz

1174

cowdy

1139

SLO-89

1028

Cadmoon

1026

Member name Posts shanef 8170 Nismo_Boy 5062 Silver_R34_GT-T 4271 Bunta 3769 Ants 3170 phatboi2010 3131 Captain Natro 2779 Keegs 2658 luke GTR 2501 t5iv 2486 Col-GTSX 2425 markimak 2389 Mr-Toy33 2331 impact_blue 2273 lilmike86 1965 LIL34 1947 SMR33 1894 Konrad 1894 FineLine 1879 Oblivion 1334 85URK 1333 Squizz 1174 cowdy 1139 SLO-89 1028 Cadmoon 1026

7th of all time... I'm happy with that :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...