Jump to content
SAU Community

Recommended Posts

Nissan Skyline R33 $10,000

95 Model Series 1

Metalic Silver, 5 Speed Manual, 70% tread on tyres.

Mods: 400R Front Bar with BN SIDES AND REAR BAR

Turbosmart Duel Stage Boost Controller

3inch genie Cat Back Exhaust, (new cat as well)

K & N Cold Air Intake

Custom Silver interia

Imported - Momo Wheel, knob and foot pedals, (same wheel as green skyline in fast fours mag few issues ago)

Full underbody LEDS, All colours,

2 x x12 Inch kenwood Subs with Customised Boot, With a Rockfed 800w Amp Mounted to boot lid.

First owner in australia, 134,000 kms, o.... , As i just moved to melb and need the cash...Hawthorn Area

Havent got any pics yet, but can arrang some if you want, Email me at [email protected]

NEED TO SELL PRICE DROP TO $10,000 o.n.o

Edited by doof
Link to comment
https://www.sau.com.au/forums/topic/120026-r33-gtst-mspec-good-nick/
Share on other sites

  • 2 weeks later...
  • 6 months later...
  • 2 weeks later...
PRICE DROP $10,000

Hey mate im realy intersted would u swap for a VT Berlina with full Calais options, V8, sunroof, silver, 17" GTS copies, tinted windows, 2 1/2" exhaust, fe2 suspension, etc always serviced exel cond.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...