Jump to content
SAU Community

R32 Gtst Vertex Body Kit

Mr Cali
 Share

Recommended Posts

Mr Cali Rising Star

Mr Cali

Posted
Posted

Hi I have a brand new vertex kit for the R32 GTST that I'm selling.

The fiberglass is in top condition and very well made.

Asking for $500 for the full kit and special price for painting and fitting can be arranged through Xclusive Colours in Wentworthville NSW if you like.

As you can see from the pic that the kit is of good quality.

Would prefer Sydney buyer as postage will be difficult for this item.

I might be able to get more then one kit.

Send me a PM if you're interested.

post-28919-1149033487.gif

post-28919-1149033503.gif

post-28919-1149033846.jpg

Link to comment
https://www.sau.com.au/forums/topic/120261-r32-gtst-vertex-body-kit/
Share on other sites
Mr Cali Rising Star

Mr Cali

Posted
  • Author
Posted (edited)

Blitz these kits are from an importor friend of mine, I was thinking of becomming a reseller of his products but wanted to gauge interest, and to offer SAU a special deal. Louie actually told to me come here as he knows some of the Admins.

No kits for the 4door, but it shouldnt be too hard to extend the side skirts if everthing else is the same at a small cost.

Booster, yes these kits are made from flexi glass, so they have even more flex then ABS plastic bars.

Patto, the kit is $500 + $550 for painting and fitting

Edited by Mr Cali
patto1234 Community Regular

patto1234

Posted
Posted

Yeh I thought that seemed a little too cheap! I was researching getting one of these kits fitted and sprayed a few months ago and this is an unbelievable price. It smashes all the other prices getting around.

If only I had the cash! :mellow:

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • Dose Pipe Sutututu
      RB25DE NEO with Haltech ECU

      By Dose Pipe Sutututu · Posted

      post up screen shots of your injector tables
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...