Jump to content
SAU Community

Recommended Posts

Hey guys, i purchased a hole saw to cut the piping hole under the washer bottle and to be safe i asked the sales person at bunnings for 3 1/2 inch so the FMIC pipes dont scrape or rattle... they gave me a 92mm which turned out to be 3 5/8 inch... I placed the hole saw over where I need to make the hole and it JUST scrapes under the washer bracket.. in other words the hole will clear the washer bottle but just barely... Is that too big?? I know most people use 3" but what other sizes you guys use?

Not bothered returning it :D

Cheers

Link to comment
https://www.sau.com.au/forums/topic/120316-fmic-installation-tight-situation/
Share on other sites

Haha thanks Madz... i read in a few threads that 3 1/2 inch was too big :D im worried that my 3 5/8 hole will be too big too... but it seemed fine when dummy fitting it under the washer bottle... i dunno mate

Cheers

Yea might just go and exchange it for a 75mm (3 inch) hole saw...

But few people have said its a tight fit with 3" and others say 3 1/2 is too big... and when i dummy fit the 3 5/8" hole saw it seemed alright... :

ok, i just went out and did some measuring. if you have the top of the hole saw where the top of a 3" hole saw would sit and just cut the hole there. if you look in the engine bay from the top you will see where the hole will go, and below it is a shelf. that shelf is about 100mm below the top so there is room.

This is the diagram from the HYBRID install guide.. if i raise the center by a few cm it should clear the 92mm hole... lol well lets hope so :D

post-23753-1149066046.jpg

I wouldn't want to move the hole so the cross pipe doesn't hit the fan blades which will be clipped.. i think i should save myself the head ache and just get a 75mm hole saw...

Edited by QRI05E

you lost me there with the fan blade bit. do you mean when you finally punch through are you worried that if the hole was accross any more it might damage the blades? you could just do it when you take the fan out to trin the blades. (easier to take the fan out to get an even cut on all blades as its only 4 bolts)

Yea if i was to take the hole any closer to the front it would bring the crossover pipe close to the blades and also throw the mounting bracket out off alignment with the engine head..

Im pretty sure if i follow the HYBRID guide it will all line up sweetly... :dry:

what i meant is that the fact that the hole was that much bigger than it needs to be that it wouldn't matter if it was moved slightly. if the hole was a tight fit then it would put the mounting brackets out of place, but as the hole is way bigger than it needs to be, so if it is moved it won't make a difference as the piping would still have quite a gap before it touches the edge of the hole.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...