Jump to content
SAU Community

Recommended Posts

hey i was wondering if any knows how to light up the skyline sign at the back?

i was thinking of putting a neon tube on the back but dont know how to connect the neon to the back light to make it switch on when i turn the lights.

anyone have another suggestion i would like to hear it thanks you..... by the way im shocking when it comes to electronic, soo i would have no idea where to start when it comes to wiring things.

post-25344-1149236738.jpg

Link to comment
https://www.sau.com.au/forums/topic/120645-light-up-skyline-sign/
Share on other sites

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Thats my car in that pic

i used 14 hi bright red LEDs run in series with a resister, then they are tapped into the brake light feed from the rear lights for power

i tried a neon first, wasn't bright enough and didn't fit in there very nicely.;

it was a S1 clear panel, that was sprayed the cars colour, then sanded off the paint from the letters.

these lightup panels were a factory option. look around importers sheds and the like, they might have one lying around. justjap.com, try them

the option from factory looks no where as good as craved's car looks though. The factory option looks like some one went over it with glow in the dark paint.

there are small kits u can buy at jaycar that consist of bars of say 5 LED's that are 12V DC already so its perfect for ur car. they're quite bright i think, look at the MCD rating of LED's to determine their brightness.

ie. those little LEDs u see to indicate stuff are like 15mcds. there are 6000 ones etc. the single ones u will need a small board consisting of a voltage regulator and 2 capacitors or so depending on the voltage of the LED's, most likely they wont be 12..if they are its better to use such a regulator anyway.

i'd probably suggest u use one or two CCFL tubes instead. Theyre really thin and much brighter than neons. The reason being that led's will have regions of brightness etc. ie. the centre of the led, then dim away till the next one and so on. It wont look completely even whereas two CCFL tubes i think would give just the blue glow etc. one just above the writing and one just below. u could be creative and put a little mirror next to the ccfl making all the light go in the middle only.

Thats my car in that pic

i used 14 hi bright red LEDs run in series with a resister, then they are tapped into the brake light feed from the rear lights for power

i tried a neon first, wasn't bright enough and didn't fit in there very nicely.;

it was a S1 clear panel, that was sprayed the cars colour, then sanded off the paint from the letters.

that sounds easy but do you think you can take pic of it and show me steps by steps of how you did that?

that would be great if you can... if you wanna send it to my email its.... [email protected]

thankz

Here is my "SKYLINE" backlight.

post-1811-1149328684.jpg

This is how i done it myself :thumbsup:

The "SKYLINE" facia (S1 R33) was first sprayed the same colour as my car. It is advisable to use a few coats of black paint, then spray your colour as required. The black paint should not allow the light to come through.

I then used my Dremal tool to cut out the rear plastic of the facia. Do not attempt to pry the facia apart, you will only end up cracking the plactic.

post-1811-1149329058.jpg

Then i used a sharp blade, off a Stanly knife (remove the blade from the Stanley knife), to carefully cut off the paint from each letter. (Not as hard/long as i thought it would be :)).

post-1811-1149329173.jpg

Using a Jaycar "bread board" and my electronic experience, i positioned two hi-intensity LEDs, in series with resistors, in between each letter. This was done to try and minimize the focus of the LEDs. YES, it is damn bright :banana:. It may also help to file the top of the LED's, this will disperse the light better.

post-1811-1149329318.jpg

It is now ready to be secured into position, I just used some 'Locktite 406' super glue and a small plastic tab at each end. Once fixed, i coated/sealed the rear facia with a good layer of sicaflex, to ensure it is as water resistant as the original.

post-1811-1149329540.jpg

I had to remove one of the 4 mounting bolts to allow the wires to enter the boot. Using a multimeter i found the wire that lights the night lights and spliced the 12V wires to it. The ground wire was bolted to an existing ground point. Sorry, i forgot what colour the 12V supply wire is :(.

post-1811-1149330254.jpg

Hope that helps ;)

Good Luck

Alan

Awsome job Al! I have an R32 and have thought about this many a time but couldn't figure out how to get several LED's on the go without wiring each LED individually with thier own resistors but if you can get the common power boards that might just be the trick!

I think I'll only use it as a third brake light though

Edited by ellie

On a 32 it is a lot harder as the letters are imbedded into the bar and the bar is not transparent. You will need to cut out each letter carefully (very hard), then fix a red diffuser behind the letters and seal them, then place the LED's behind that. A lot of work :thumbsup:

I decided to use it as a night light as the LED's are not bright enough during the day, certainly not good enough as a third brake light. Also the police may state that the "flashing" letters (when in traffic and appling brakes numerous times) will be a distraction to other motorists.

Good Luck

PS: Funkymonkey has made the SKYLINE backlight for the his previous R32, maybe he can help you out.

Here is my "SKYLINE" backlight.

post-1811-1149328684.jpg

This is how i done it myself :P

The "SKYLINE" facia (S1 R33) was first sprayed the same colour as my car. It is advisable to use a few coats of black paint, then spray your colour as required. The black paint should not allow the light to come through.

I then used my Dremal tool to cut out the rear plastic of the facia. Do not attempt to pry the facia apart, you will only end up cracking the plactic.

post-1811-1149329058.jpg

Then i used a sharp blade, off a Stanly knife (remove the blade from the Stanley knife), to carefully cut off the paint from each letter. (Not as hard/long as i thought it would be :().

post-1811-1149329173.jpg

Using a Jaycar "bread board" and my electronic experience, i positioned two hi-intensity LEDs, in series with resistors, in between each letter. This was done to try and minimize the focus of the LEDs. YES, it is damn bright :P. It may also help to file the top of the LED's, this will disperse the light better.

post-1811-1149329318.jpg

It is now ready to be secured into position, I just used some 'Locktite 406' super glue and a small plastic tab at each end. Once fixed, i coated/sealed the rear facia with a good layer of sicaflex, to ensure it is as water resistant as the original.

post-1811-1149329540.jpg

I had to remove one of the 4 mounting bolts to allow the wires to enter the boot. Using a multimeter i found the wire that lights the night lights and spliced the 12V wires to it. The ground wire was bolted to an existing ground point. Sorry, i forgot what colour the 12V supply wire is :D.

post-1811-1149330254.jpg

Hope that helps ;)

Good Luck

Alan

hey thankz for the picture and everything, do you think you can show me a closer look at the circuit board bcos i wouldnt have a clue on where to solder the LED and where to put the resistor or which resistor to use.

sorry im like a total newbie when it comes to electronic circuit

  • 2 weeks later...

No probs, will do soon.

The clear "SKYLINE" panel is off a S1. All S1 Skylines have this clear panel between the rear indicators, you then paint it (to match the body colour) and use a fine blade to cut the paint off the lettering.

Can not use a S2 pannel as it is made from black plastic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...