Jump to content
SAU Community

Recommended Posts

Hey there, just got a car I'm looking at buying inspected and although there were a fair few other things wrong with it, the one i'm majorly concerned with is one listed as requiring early attention and described as. Front wheels, one side is 20mm further forward than other. It says that it will require specialist attention to acertain the reason for it. I rang a few places and they all seemed to think the most likely reason for it would have been an accident at some stage. Just wondering if anyone has had any experience with a similar problem or knows how likely it is that this could be a serious problem? I don't want to buy the car only to find out that it has been crashed and has some serious chasis damage.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/121649-wheel-mis-alignment/
Share on other sites

Hey there, just got a car I'm looking at buying inspected and although there were a fair few other things wrong with it, the one i'm majorly concerned with is one listed as requiring early attention and described as. Front wheels, one side is 20mm further forward than other. It says that it will require specialist attention to acertain the reason for it. I rang a few places and they all seemed to think the most likely reason for it would have been an accident at some stage. Just wondering if anyone has had any experience with a similar problem or knows how likely it is that this could be a serious problem? I don't want to buy the car only to find out that it has been crashed and has some serious chasis damage.

Thanks.

It could be something as simple asa worn radius rod bush, or something as bad as a bent chassis rail. Any decent suspension shop should be able to do a complete wheel alignment check and point you in the right direction.

:) Cheers :P

I work for a joint what does Wheels Tyres and Alignments, and the front wheel on the left side of the car should be set forward a little more than the right side, cos of the "australian road conditions" we run a higher road camber here, so the left wheel is set forward a little bit to allow for the car to drive straight on the road.

Hmm, if it's chasis damage (worst case scenario) then it could very well be irrepairable right? I've never heard of one wheel being set forward a little more than the other... would it be set forward as much as 20mm?

What would be my best course of action to get the problem diagnosed? Someone mentioned maybe take it to a wreckers and they have a machine there to check the body alignment using the datum points etc.

Hmm, if it's chasis damage (worst case scenario) then it could very well be irrepairable right? I've never heard of one wheel being set forward a little more than the other... would it be set forward as much as 20mm?

What would be my best course of action to get the problem diagnosed? Someone mentioned maybe take it to a wreckers and they have a machine there to check the body alignment using the datum points etc.

That would be a panel beater, make sure they have the data for a Skyline

Yep more caster on the LHS front to stop the drift into the gutter caused by the camber of the round.

But 20 mm is a bit too much

:P cheers :mad:

Hey guys,

This is actually my skyline he is talking about.

Here are two wheel alignment read-outs one (bobjane) before the white line gear was put in and one (wilkinsons) after the white line one was put in.

They were done less then a month apart.

The bob jane shows castor left +6'33" right +6'48"

The wilkinsons shows castor left +7'38" right +5'38"

Isnt this proof that all that has happened is that wilkinsons has set the whiteline adjustable caster up for aussie roads? also wilkinsons never mentioned any problems what so ever so I really think eveyrthings ok.

I will be ringing on monday to confirm, as this sale is hinging on this car being straight or not.

EDIT: the bobjane readout was from one of those crappy ribbon printers so it didnt scan well but you guys can make out the numbers yeah? its much easier to read from the original.

post-8656-1149936988.jpg

post-8656-1149937001.jpg

Edited by noise

If it is the castor setting an easy check would be to climb under and measure from the centre of the front castor rod bolt to the first of the 2 on the lower control arm.

If one's shorter than the other then i'd say that it's all in the adjustment.

If it is the castor setting an easy check would be to climb under and measure from the centre of the front castor rod bolt to the first of the 2 on the lower control arm.

If one's shorter than the other then i'd say that it's all in the adjustment.

I just got down and had a look, you can see more yellow on the right one I think it was and less on the left. Considering the angle they are sitting on is how you adjust them and one is sitting out further I would say the mystery has been solved, will confirm with the suspension guys on Monday.

RAC is getting a letter of complaint next week for sending out a mechanic who wrote a false and misleading statements about my car which resulted in the sale of the car being stalled and possibly called off.

Not happy :ermm:

Edited by noise

Dude if there was a mojor problem Wilkinson would have told you. I really doubt there is an issue. Sounds like alignment settings to me. The RAC job is to pick faults. They are normally mechanics, not alignment experts so i would take on board the oil leaks etc they point out, but probably not the alignment.

Regards

R Dirty 3

Sorry you mentioned bob jane... I zoned out after that..

Yes 20 mm is a bit much for castor, but was the RAC telling you the truth. got the same problem in Adelaide with RAA car inspectors, tell ya lies and dont know what they are on about.

Bob Janes here in Adelaide are prolly the worst people in the world to let near your car. I dont know what they are like anywhere else in the country, but here in Adelaide, they will tell you that your car needs half the front end rebuilt just to get the work... and here in adelaide a few of my mates own the old classic holdens and chevs, and every bob janes they have gone to, dont know how to wheel align there cars, so if you need your car to be wheel aligned to specs or to match Aust road conditions, I would honestly look for someone in a small local business, cos they have to do it right, else no one would goback to them.

Just my 2 cents worth on wheel alignments from bob janes.

Sorry if it seems like i am havinga cry over businesses, but i just offer my advice.

WARNING to anyone buying or selling your car, make sure you tell the mechanic to ignore anything after market on the car otherwise they will list aftermarket parts as problems that need fixing.

exhaust, pedals, airpod etc.

The mechanic could have just looked under the wheel arch and seen the BRIGHT YELLOW adjustable caster rod thing and measured it to make sure it was all ok.

Dodgy as f#*$

Edited by noise

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...