Jump to content
SAU Community

Recommended Posts

you can thread the wires up the pillar pretty easily. just remove the kickplate and the cover on the side of the foot well, then remove the rubber from the door frame. you can slide the wires up the side of the A-pillar cover and out the hole from the tweeter cover.

stock split wires come together deep in the dash. Dont bother to use them mate, they are pissy wire anyway.

As terminal said, I ran my tweeter wires up behind the kickplates, then between the dash and the body and up into the A-pillar.

woofer(meaning, for splits) wires I just used the stock wires...i know, but i cbf'ed to replace em.

My amp is also under my passenger seat. Just remove the stock airvent under there and run the wires through there. I put some MDF below the carpet and drilled/screwed the amp onto that.

  • 1 year later...

all i did was flick out the cover with a screw driver. unscrew the stock tweeter.. throw that sumwhere ull never find it. run your new wire down tha a piller. n poke it out on the door side.. poke it behind the dash with a screw driver, mount your cross over under the kick panel on the drivers side and ecu cover on passenger side. stockwires for woofer.. jsut take out the door trim (yes there is a screw in the bit that you pull on to close! (tooke me a while :banana:) then i just pulled out the head unit worked out what was the front speaker wire head unit to amp imput on x over. and what that was connected to goes to your woofer out put on the x over. took me like hr n half 2 hrs to do a semi ligit job... also i did mine in pares like both the tweeters mounted, both the woofers mounted, etc etc gd luck

that looks SICK! well done ! and woulda saved a HEAP of time

I am going thru the epic stereo install from hell at the moment haha.. I am just worried I didnt give em enough wattage- 50w RMS all round - I have the Hertz 165's too - so hopefully that gives them enough power

what i did with mine....
  • 10 months later...
I put mine where the stock ones came. I did not have stock ones come with the car, so i drilled holes and put there in there.

To remove that A pillar part, you need to do the following (easiest this way)

- Remove front seats

- Remove door sills/kick panels

- Remove the covers for the seatbelt things

- Remove A pillar thing

Trust me when I say, this is NOTHING compared to removing the rear bar! Just a quick run down of the rear bar

- Remove boot carpet

- Remove holders/plastic caps etc

- Remove plastic from sides

- Remove wall carpet

- Remove rear bar

That takes about 2h, compared to the A pillar ~30 minutes.

In my system, I LOVE the tweeters placed where they are. My Hertz HSK165's are splits, with woofers in the doors and tweeters on the A Pilar. As there is no midrange speaker, the balance is made via tuning the EQ.

Hertz does actually stock midrange speakers, but not on the RS4.

If you want a comment on my sound systems pumpage, I honestly dont think it could sound any better than the way it is, ask Ian, aka humble.

i was skimming over this to see how to get the a pillar plastic off and just had a question. why does the seat need to come out??

that looks SICK! well done ! and woulda saved a HEAP of time

I am going thru the epic stereo install from hell at the moment haha.. I am just worried I didnt give em enough wattage- 50w RMS all round - I have the Hertz 165's too - so hopefully that gives them enough power

thats what mine have, needs more :laugh:

i was skimming over this to see how to get the a pillar plastic off and just had a question. why does the seat need to come out??

Both AlexCim and myself mounted amps under our seats :D

my stock system still running the stock amp but aftermarket head unit, no need to upgrade my system.

unless it was done in japan ? cause it pumps pretty damn good ;):banana:

and no room underseats for amps, got electric heated seats.

so i saved myself about 800bucks in speakers :D HIGH FIVE!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...