Jump to content
SAU Community

Recommended Posts

I'm not sure on pricing but one mistake I made is not checking hte part before it was installed.

Make sure you do this!!! Mainly checking for welds and other restrictions.. all welds should either be on the outside or ground back so not to cause any undue turbulance and restriction.

ok mate, this is a really bad question to ask the people here, as everyone is going to rave about their own exhaust, or spit out brand names that cost thousands...

my opinion is that an exhaust, as long as its flow is fine, does not need to have a brand name or anything like that in order to make power.

I think the loudness of an exhaust is related to

- its age

- type of muffler

- presence/absence of resonator/second muffler

Thus... when factoring in price, loudness, and power, i believe the best option is to get a setup that comprises a custom cat-back and cheap dump/front off the forums

So keeping in mind that a "turbo-back" exhaust consists of

- dump pipe

- front pipe

- cat

- cat-back

i reccommend the following:

1) dump/front pipe in one from BATMBL: http://www.skylinesaustralia.com/forums/in...showtopic=74022

2) 3" cat from BATMBL: http://www.skylinesaustralia.com/forums/in...showtopic=74022

3) custom 3" mandrel-bent exhaust including new muffler and resonator: see your local exhaust shop and shop around for a few prices...

This should all up cost you less than $1000 and see you a decent increase in the seat-o-the-pants-o-meter

cheers,

Warren

I'd just go mild steel from a local exhaust shop.

I paid $600 (without a hi-flow cat), that was a new dump and full 3" mandrel exhaust.

Cheaper than stainless... and realistically, you dont need stainless.

You cant see it, so who cares?

personally i'd go the x-force mild steel from cat back. $699 from justjap (go to your local shop and ask them for a price and if justjap are cheaper then see if they can match or better that price). if you go with the batmbl dump/front pipe and cat you are up to over $600 and still have to get a cat back system, which you won't get for under $200 as it costs about that much just for a decent muffler.

Edited by mad082

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...