Jump to content
SAU Community

Recommended Posts

I Guys & Gals

Put in stereo (& alarm) on weekend in my S2 R33...Its all good except the DIN i used was not a nissan one but a universal & basically its a cheap piece of shite which does not fit (gaps etc)

Anyhow did a search & apparently the genuine nissan pulsar one fits in perfectly & is availble for $30-$35 which sounds good to me but then i read that a toyota one is exactly the same & is only $10...Is this true & if so which model toyota DIN should i buy?

Also i have an alpine 9831 MP3 HU & like others have encountered the surround does not fit...how have people gotten around this & is the surround supposed to sit behind the actual dash or in front?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/123749-din-pocket-hu-surround/
Share on other sites

If i were you i would just go to nissan and get a genuine one..

otherwise you will end up with a $10 din that doesnt even fit..

otherwise try powerplay imports

they usually give sau members good deals

http://www.powerplayimports.com/

Give them a ring.. but they wont be open til tues due to the powerplay track day..

hope that helps..

Also i have an alpine 9831 MP3 HU & like others have encountered the surround does not fit...how have people gotten around this & is the surround supposed to sit behind the actual dash or in front?

I had no problems fitting the 9831 into my car.

Follow this guide on the HU surround. http://r33stereo.groovesystems.net/

You have to drill new holes. I have the same HU as in the guide, but i cbf'ed drilling the holes so I just removed the plastic surround and didnt use it.

As for the poket din, line it up and use eletrical tape to secure it or use cable ties. The one I used was a generic one and it fited perfectly after tieing it up with tape.

Do you have a pic of your pocket?

You can buy the pocket off me for $10? Where abouts are ya?

Follow this guide on the HU surround. http://r33stereo.groovesystems.net/

You have to drill new holes. I have the same HU as in the guide, but i cbf'ed drilling the holes so I just removed the plastic surround and didnt use it.

As for the poket din, line it up and use eletrical tape to secure it or use cable ties. The one I used was a generic one and it fited perfectly after tieing it up with tape.

Do you have a pic of your pocket?

You can buy the pocket off me for $10? Where abouts are ya?

Yea i have that guide but i wanted the surround to sit on outside of the dash, not behind like in the guide where he has pushed his HU back so that it all fits behind

Re the pocket thanks but no thanks i would rather one that actually fits correctly rather than taping it etc

Thanks anyhow

I have used the guide. My surround sits nicely behind the fascia, can post a pic up when I go home for lunch. When I first bought the car the owner had just upgraded from the stock stereo and had the surround on the outside, it looked like crap. I sold that one and upgraded to a Nakamichi.

As for the Din pocket, I went to an Audio store and asked if they had something that would fit, ironically they had fitted a system to a brand new Nissan Navara earlier and gave it to me for $5. Perhaps you could try asking around.

Edit: Here you go. Please excuse the layer of dust on my interior

cimg07145mi.th.jpg

Edited by MintR33
I have used the guide. My surround sits nicely behind the fascia, can post a pic up when I go home for lunch. When I first bought the car the owner had just upgraded from the stock stereo and had the surround on the outside, it looked like crap. I sold that one and upgraded to a Nakamichi.

As for the Din pocket, I went to an Audio store and asked if they had something that would fit, ironically they had fitted a system to a brand new Nissan Navara earlier and gave it to me for $5. Perhaps you could try asking around.

Edit: Here you go. Please excuse the layer of dust on my interior

cimg07145mi.th.jpg

It does look good behind...all nice & flat...ok might consider doing it that way then

would the navara DIN be the same as a pulsar one?

Thanks

nissan pockets are nissan pockets. they all come from the same bin.

in regard to the toyota one - NOPE! the nissan one will boilt straight in. I usually keep them on hand for $28 (out currently.)

If you havent heard of it then chances are you haven't heard of alot of these brands: Click (go to Exotica)

Basically Nakamichi is a high end SQ brand that became famous in the 80's (but has been around since the 40's) for innovating alot of the cassette deck technology of the time. These day's they are largely overlooked, mainly because they are quite expensive and not widely available. About 99% of Nak's R&D goes into making really high fidelity sound reproduction, and as such the appearance of thier units is kept minamalistic and direcected at complimenting the rest of the vehicle's interior (hence the reason for no bling looking screens or chrome buttons).

At the time of purchase (2004) my h/u was retailing at approx $1600 from memory. I think you can buy them now for around $800, but my model does not play MP3.

Here's one of their new products that looks extreemly nice, its their new indash DVD/TV tuner:

indv7.jpg

For more info visit the website.

http://www.nakamichi.com/

Edited by MintR33
Do you sell Nak stuff Chris?

If so do you know if you are able to get hold of Nakamichi SP-C6500 splits?

I do but not a lot of it.

I can do decks but not speakers (I'll check though.)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...