Jump to content
SAU Community

Recommended Posts

My window on the R32 fell down inside the door and now won't wind back up. Just when I closed it today it made a lound clunk noise and I went to open it again. That's when it just slid down. It doesn't sound like it's rattling or anything so I don't know if it's fallen of its tracks or something else. I will be taking the door apart tomorrow and removing the sound deadening to have a look. I just want to know what the general problem could be as I don't really know how the window mechanism operates.

Anyone know how to remove the assembly. I've taken the 4 bolts of and tried lifting the whole thing out including the window, but there's not enough clearance at the top for it to come out. Do I need to remove the window first? I've attacted a picture of the 4 botls that I took off.

post-3291-1152070276.jpg

  • 4 years later...

on another note, does anyone know if it's possible to get the window to go back up and stay up? (given that it will probably take at least 2 days to get a new assembly sent here if it's the cause)

Edited by bozodos

pillars.. maybe to the roof.. unless you wanted to jam a block underneath? maybe more difficult though.. Just do the bogan thing.. plastic and tape around the outside..

  • 2 weeks later...

FFS. new assembly has arrived, and went in fine, however I was foolishly trying to do the locating nuts up as tight as they were beforehand and one snapped off. The other snapped off taking it off.

Low quality pics show what I mean here, the red circle is the head of the nut which has snapped off. Is it possible to get these re threaded in some way or am I just going to have to get a new window. fml

09272010024.jpg

09272010025.jpg

1. You have a red square, and blue circles.. i am going to assume the red square (not circle) is the head of the bolt/threaded bar and the blue circles are where they snapped..

what is on the other side of the threaded bar, or did you screw the threaded bar in? if so i would look at drilling a hole in the middle of the threaded bar and using a screw extractor kit to get it out and replace it..

is that what you are looking to do? pics are pretty bad..

pretty much, and yeah after i'd uploaded them to my computer noticed that i had gunk on my phone camera lens.

there is a flat side like a rivet on the other side of the threads, going to look at just getting another window before the thread replacement option. my inital reaction was FFFFUUUUUUUUUUUUUUUUU. I figured that I am probably not the first person to do this, but wasn't sure if it was one of those kind of things which are set into the glass at the factory while it is still hot etc. My failure was in attempting to tighten them up to the point as they were when I took the window out.

Spose that will teach me to tighten things up too fkn much.

Edited by bozodos

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...