Jump to content
SAU Community

Recommended Posts

Hi guys

Heres the #2 GB for the CATCO 3" high flow cats!

The 3 types of 3" cats available as bolt on for the R32 GTST/GTR, R33 GTST/GTR & R34 GTT Skylines are as follows (These same cats are also available bolt on for the S14/S15 200SX)

3" small body BOLT ON Catco cat (ceramic inside) - GB price only $160 including delivery

3" large body BOLT ON Catco cat (ceramic inside) - GB price only $230 including delivery

3" metal Catco cat BOLT ON (5" round body, 200csi metal inside - 706.2 CFM!) - GB price only $360 including delivery (They are $10 more than previous GB due to fluctuating costs on this particular cat)

Competitor cats either have a 200csi substrate with 4" body (Metal Cat) or 300csi substrate with 4" body (Magic Cat), making them inferior in flow to the CATCO metal cat.

ALL 3 of these CATCO CATS comply with EPA and CARB requirements and are made in the USA. There has been 100's sold through the SAU forums and not one problem has occured, EVER! so you know you are buying quality!

Take advantage of these rare GB prices! A min of 10 people is needed and it can be any one of the cats above. Note the metal CATCO cat is $80 cheaper and the price includes delivery!

Please list your interest in the thread below by stating which cat you are after and which car its for. All payments must be in by Tuesday 18/07/06. BATMBL will provide bank account details through PM, so please also send your address details this way to him.

Hey Michael,

May as well get a 3"metal sub cat to go with my split dump thats on its way from the other GB.

So 1x 3"metal cat for R32 GTSt please!

Thanks,

Rhett

put me in for this one please, can you give me a dimension length wise please., flange to flange. thanks

3" metal Catco cat BOLT ON (5" round body, 200csi metal inside - 706.2 CFM!) - GB price only $360 including delivery (They are $10 more than previous GB due to fluctuating costs on this particular cat)

godzl1975,

The length from flange to flange is about 315-318mm. (Cant quite get the exact measurement because of the measuring tape curving over the cat). The same bolt on cat is used for R32 and R33 GTST or GTR.

cheers

godzl1975,

The length from flange to flange is about 315-318mm. (Cant quite get the exact measurement because of the measuring tape curving over the cat). The same bolt on cat is used for R32 and R33 GTST or GTR.

cheers

ok kool....let you know if it will bolt st8 on thanks aaron

hi guys

6 cats were sent out today. the list has been updated, so check if yours was sent. Everyone else will get their cat sent out tomorrow (Thu).

All of you should receive your cat either this Fri or next Mon-Wed depending on how long it takes to receive registered post from Sydney.

A BIG thank you to all who participated in this GB and due to the success we may have another one soon.

cheers guys

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...