Jump to content
SAU Community

Recommended Posts

Well here is my problem...

Plug in the pfc. The hand controller doesnt turn on. Put keys in and turn it to ACC. The hand controller turns on. Turn off the boost controller unit.

Turn the keys to "ON". At this stage the engine light and the exhaust temp sensor flashes repeatedly and I can hear a tapping noise comming from the fuel pump. Fuel pump seems to prime. I wait awhile crank the engine to try and start it and it wont budge!

Plug back the stock ECU and everything works, car starts, just doesnt like the PFC.

All alarms are turned off. (That I know of)

At first I thought it was a faulty PFC, but I tried another PFC and it did the same thing.

S1 RB25DET 5 Speed Manual.

I have no idea what is wrong. Suspecting its a wiring problem? The stock ECU is an old one with some sort of diagnostic knob at the back of it. :

Edit: In case people dont read this was fixed, cause is explined here: http://www.skylinesaustralia.com/forums/in...t&p=2327813

Link to comment
https://www.sau.com.au/forums/topic/125792-how-to-install-a-powerfc/
Share on other sites

Ill take the stock ECU out tommorrow and get some pictures.

Hmm had a re-read of paulr33's pfc faq and this might be my problem?

"Some cars only (for some strange reason) have half gauge wiring running from the battery to the ECU. This works fine for the factory computer but the PowerFC needs the full 12volts. You can simply run new 12volt wire from the battery to the ECU and this should correct this. This problem has been experienced by at least two members previously (both in R33 GTST)"?

I am unsure how the 12v feed will affect the PFC, other than "it doesnt work", I know the hand controller runs of a 5v feed. Try this.

FC in and hand controller in

turn to ACC

check out SENSOR SW CHECK under ETC

post up what sensors are in black (backlight) highlited

Hmm ok I have some pics of my "stock" ECU. See below.

This is what I just tried before..

I tried plugging in the PFC again. This time I took note of what happened.

Plugged in the wiring loom.

Plug in hand controller

Disable alarm

Turn the key to ACC. Nothing! Hand controller doesnt turn on! wtf?

Turn the key to ON, Hand controller comes up APEXI Screen then it just freezes at the "RB25DET" screen.

All this is happening whilst the engine light and exhaust temp sensors are flashing and the ticking sound is heard from the fuel tank.

Once again unplug everything and put stock ECU back and everything works fine.

Weird thing at back of ECU:

post-18389-1152695161.jpg

ECU Mounted:

post-18389-1152695196.jpg

Hmm after talking to people. Seems like the pic above is a stock ecu and nothing special about it.

This leads me to the wiring. The plug loom u see there is for the AVCR.

Or possibly the pfc isnt recieving enough volts at ACC to start up?

As the stock ECU only needs 8v to start, while the pfc needs the full 12v?

Hmmmmm

The PFC h/c and fuel pump prime should only show/be heard when in the on position, then a further turn to start will have the car start, letting go of the key returns it to the on position where the car continues to run.

Check the sensor sw screen and post up ALL of the values, preferably take a photo of the screen and post it.

joel, from what Victor has told me. it stays on the RB25DET version screen and doesn't continue through that point to the menu's. he was able to get in there ONCE while at hitmans to turn off the boost control.

he told me also that the AVCR doesn't have any values for INJ/TPS etc coming to it.

also what i found was strange, he said it doesn't Crank over when turning the key to start.

ahh no problems...

When my pfc was in for repairs it would hang on the intro screen when it wasn't receiving certian inputs. i.e simply running power through it. Once installed it was fine.

Its also been known for the plug to be slightly off and not done up straight causing it too to hang on the intro screen.

But yes if the avcr isn't receiving values either then something is definitely up. :unsure:

I would check removing the ecu hasn't broken/distrubed the work done on the loom when the avcr was isntalled.

should have elaborated a little..

the AVCR works fine when using the std ECU, but not at all when using the power FC.

edit - did yours crank over and just not start when your PFC fried ?

Edited by Craved

Havent checked fuses.. But with the std ECU works fine.

It may be the PFC simply not recieving enough volts. or wiring missmatch, though I cant see why.

Ill try jump starting it via jumper leads tommorow. Unless its bad to do this. :

It all too confusing right now..

jump starting it is, but if wont go past the rb25det version display then theres no point. the FC is locking up for some reason.

turn the car off.

hold up on the hand controller

turn it on.

what comes up?

d00dz I wouldnt be experimenting to much especialy with straight power ! I know nothing about this but hard wire jumping the car or Ecu cant be good ... get it tested or give it A fresh 12 volts but lighty fused...

Get it tested Professionaly so you know

You dont want to blow any Warrenties because your frustrated !

jump starting a car with a PFC is no different to stock ecu.

ive done it before twice and it works just as normal (as its supposed to).

it sounds like you have the wierd wiring (not 12v guage) at a guess

Hi Guys

had exactly the same prob the little blue relay next to the battery in the boot ticks like mad. iafter ripping half the dash apart and checking all the voltages from the pinouts it was just the fuse the fuse box has two rows top to bottom its the left hand row sixthfuse up runs fine on old ecu -nothing but start screen on PFC

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Price seems pretty good to me. Also seems a hell of a lot cheaper then buying another vehicle that only ever gets used for towing.  I'm a long way from you mate, I'm a couple of hours out of Brizzy. 
    • New [400]Z, they're available in manual and you don't have to worry about parts scarcity. 
    • Just planning to have the wiring neat and hide as much as possible.
    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
×
×
  • Create New...