Jump to content
SAU Community

Recommended Posts

I reckon that turbo can support a lot more airflow (power potential) than an RB25 could reliably withstand so a bit pointless unless you beefed up the internals . To get the boost threshold down to an acceptable point for a road car would mean using a small AR ratio exhaust housing so the 750 odd Hp compressor is wasted .

As Chris said you don't hear of these things surging , guesstimate only but HKS may have done the cover like that knowing that heroes like to put big turbos on small engines with small AR exhaust housings . By small I mean under 2L 4's .

Not sure what you mean by "efficient boost" . Airflow makes for power and pressure just moves it along . I have been told that these wheels make their greatest efficiency at surprisingly low pressure and flow rate but the "islands" are very long meaning that they work over a wide range of flow and pressure ratio . Its a pity Garrett dont make a 76mm version of this wheel because it would be a good thing with a GT35 turbine .

Cheers .

the holes on the comp cover are a workaround for compressor surging

it allows air to enter onto the compressor wheel on the outer edge to balance out the some of intake sucking, which is commonly associated with surging. think of it as an anti surging device.

the bulk of the air enters the snout, thanks to the vacuum effect of the compressor wheel sucking in air, but a very small amount enters through the holes also to side step around surge

:)

The ported holes are there to assist in reducing compressor surge so that the air enters the compressor housing around the compressor not through it.

They are also meant to help stabilise the shaft when at high shaft speeds to help reduce turbulance which creates vibrations.

They are there to help at a very high level of boost and if boost preasure is run outside the capacity of the compressor wheel creating surge then the vacuum effectivly bypasses the air through the comp ports and past the compressor wheel.

Also will this turbo go good on a rb25det or will there be a bit of lag, also what will

be the max efficient boost.

Depending on the size of the rear exhaust housing I have a t04z with a.81 housing and Ill be running 2bar of boost through my RB25 hopefully It will be at full boost by 4 .5 to 5000 rpm

I'm skeptical will see 2bar @ 4500rpm with a t04z... you'd need some very well matched cams and some agressive tuning to do so.

Probably closer to the 5k mark as you say.

I saw 24psi around 4200-4400rpm depending on gear/load with a GT30/.82.

However but that wasnt street fuel so it had some super angry timing numbers screwed into it... cause we could :dry:

Definately post results when your done though dude.

It'll be interesting to see vs what i had with the GT30 :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...