Jump to content
SAU Community

Recommended Posts

yeah silver I'd go as far to say the oil cooler is not working properly at all.

In the GTR running around 260kw atw my oil temp sits between 80 and 90 all the time, and certainly doesn't go up just cruising on the free way. The figures you have sound about normal for a car without any oil cooler.

You really need to cut out that splash gauge and preferably fit a louvered extraction vent or at least do a swiss cheese job on it. then build a little duct around it running up to the opening in your front bar. your welcome to have a look at mine if you need some inspiration.

yeah well the way it's mounted now is practically in a sealed box so it's doing fark all cooling. except a small radiation effect. you may as well have installed it in the boot, or your neighbours car for all the cooling benefit you're getting! lol

Just for reference the R33 gtst in the driveway sits at 79 degrees all day everyday regardless of stop/start or highway driving. It moves around 2-3 degrees when you give it some for a while...

Is the rb20 different?

Would of thought it'd be a good idea to get a thermostat and set the oil temp abit lower (say mid to low 70s) will make the engine run cooler and make abit more power too (or so i read in speed lol)

Sorry my bad, thats water temp that sits just under 80 degrees not oil temp, oil temp is slightly higher as ud expect, sorry i got confused for a sec hehe

If you don't agree with running oil slightly cooler being an advantage thats your opinion, the magazine i read obviously feels differently, personally i don't care either way lol!

Edited by jazza08

is there an actual benefit to having the oil at 50 degrees over 80 degrees ?? for example ..

if the cooler keeps it at 80 all the time, would you see any benefit with performance or longevity if it was at 50 degrees instead.

I think 50 might be abit low, but by keeping core engine temps lower the parts operate at a lower temp and will last longer and perform better. Ill have a look later but what i saw was something along those lines! It wasnt a MAJOR drop in oil temp like 30 degrees like you mentioned tho dude, more like low-mid 70s i think!

Im sure someone with abit more knowledge could input on this if they had a read...

What I mean guys, is that going below a certian temperature point where there is no real advantage. Oil works best between 70-100C. Going too cool and the additives are not functioning in their optimum temp range and the oil viscosity is getting too thick.

I'm not saying oil coolers are no good, thats misinterpreting. It means using oil coolers to keep oil in this range for heavily modified cars. It is good to keep the oil temp as close to the coolant temp as possible. If there is major differential, then an oil cooler is needed.

And jazza08, what magazine/article are u referring to? If running cold oil was the bomb, then we might aswell run around with 30C thermostats too.Chasing more hp outta your motor by running cold oil certianly is the wrong way to go about things! If that were the case we'd put our cars on the dyno cold!

Put your car on the dyno cold and expect things to blow up as they aren't at operating temp... ill go have a look abit later through some of the speed/hpi n any other mags i have to see where i read it coz i cant remember off the top of my head!

30 degree thermo's would obvioulsy create problems with the parts running too cold which they aren't suited for, however a few degree's lower i read wasnt such a bad thing. Who knows ill report back some findings i could be way off lol

Ok this is what i was talking about, taken from Perth street mag, even though its a v8 the principles of a cooler motor/parts should apply to all engines.

"With new themostat in place, the engine typically runs 10 degrees cooler but still remains within the acceptable bounds for the standard PCM (above 70 degrees). The standard themo opens at 93deg and is fully open at 105deg. The new thermo starts to open at 80deg and is fully open by 87deg. As a result the enginer runs a higher ignition advance, normally between 5 to 7deg more than normal. At cruise rpm this additional timing is noticeable in the seat of the pants, giving snappier accel and throttle response. With the thermo fitted to a BA GT the peak power result at the wheels rose 3kW but the real story lies in the torque curve which was reaised across the majority of the rev range, with a peak gain of 100N at the wheels"

This is where i read this and got the idea from! Nismo offer a lower temp thermostat for skylines, obviously Nissan must think that its some sort of gain?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...