Jump to content
SAU Community

Recommended Posts

Needed a roof rack in a hurry.

Used some 25mm OD pipe, Cyclone scaffold tees, 25mm ID clear plastic tube, black paint and duct tape.

The horizontal section of the tees needed flattening a bit to more nearly be the shape of the rails.Pipe was cut 920 for back, and 945 front. They are different, and the front was cut a bit short so it can be moved back to the centre of the rails. Metal parts were sprayed matt black and the tube was slit along its length to make it easier. Duct tape was wrapped around the hose, and also around rails where tees were clamped.

After using I had to move the front cross piece back to the centre because of wind noise.

Total cost if buying all the bits, about $20.

0000023gj9.jpg

0000024lt7.jpg

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/
Share on other sites

just for interest's sake,toyota rav 4 roof racks are a straight bolt on for stageas. I run a pair of ex-warranty rav racks on my S2.

new from toyota they're about $280 a pair.

Justin...

I used my Subaru Racks, $350. Big difference $20. They do the same thing. lol

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2338641
Share on other sites

I used my Subaru Racks, $350. Big difference $20. They do the same thing. lol

it IS a big difference,providing you actually pay it. I got my rav racks for free,out of the warranty bin at clean up time. I have a heap of roof rack parts at home,including some rx330 aero racks. will try those on at some point as well. if they work,someone can have my rav racks if they need a set.

Justin...

Edited by fergo308
Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339114
Share on other sites

Nice work there Hugh! So when are you going to start making them enmasse and sell them on SAu in a group buy for $50? ;)

That is what is the rage lately, I am still trying to find out what I can setup a Group Buy for :cheers:

And damn, you really dont have any sunroofs, bummer :ban:

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339141
Share on other sites

i can imagine what that will do for your highway fuel consumption. i think i'll be going for a more aerodynamically designed one.

Even with my ex Subaru and Skyline racks I always had to move them back a bit from the front.

As I've said elsewhere, " if you can't afford the petrol,you can't afford a Stagea".

Anyway, racks are not usually an everyday use. The bars take 5 mins to remove. The whole idea was to make something pronto.

As far as agroup buy, The only tools needed are a hacksaw (or angle grinder) to cut the pipe, a 10mm open ender and a Stanley knife, so it is very easy to make. Not really worth the postage.

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339593
Share on other sites

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...