Jump to content
SAU Community

Roof Rack

66yostagea
 Share

Recommended Posts

66yostagea Grand Master

66yostagea

Posted
Posted (edited)

Needed a roof rack in a hurry.

Used some 25mm OD pipe, Cyclone scaffold tees, 25mm ID clear plastic tube, black paint and duct tape.

The horizontal section of the tees needed flattening a bit to more nearly be the shape of the rails.Pipe was cut 920 for back, and 945 front. They are different, and the front was cut a bit short so it can be moved back to the centre of the rails. Metal parts were sprayed matt black and the tube was slit along its length to make it easier. Duct tape was wrapped around the hose, and also around rails where tees were clamped.

After using I had to move the front cross piece back to the centre because of wind noise.

Total cost if buying all the bits, about $20.

0000023gj9.jpg

0000024lt7.jpg

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/
Share on other sites
66yostagea Grand Master

66yostagea

Posted
  • Author
Posted
just for interest's sake,toyota rav 4 roof racks are a straight bolt on for stageas. I run a pair of ex-warranty rav racks on my S2.

new from toyota they're about $280 a pair.

Justin...

I used my Subaru Racks, $350. Big difference $20. They do the same thing. lol

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2338641
Share on other sites
fergo308 Rising Star

fergo308

Posted
Posted (edited)
I used my Subaru Racks, $350. Big difference $20. They do the same thing. lol

it IS a big difference,providing you actually pay it. I got my rav racks for free,out of the warranty bin at clean up time. I have a heap of roof rack parts at home,including some rx330 aero racks. will try those on at some point as well. if they work,someone can have my rav racks if they need a set.

Justin...

Edited by fergo308
Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339114
Share on other sites
Ska Grand Master

Ska

Posted
Posted

Nice work there Hugh! So when are you going to start making them enmasse and sell them on SAu in a group buy for $50? ;)

That is what is the rage lately, I am still trying to find out what I can setup a Group Buy for :cheers:

And damn, you really dont have any sunroofs, bummer :ban:

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339141
Share on other sites
66yostagea Grand Master

66yostagea

Posted
  • Author
Posted
i can imagine what that will do for your highway fuel consumption. i think i'll be going for a more aerodynamically designed one.

Even with my ex Subaru and Skyline racks I always had to move them back a bit from the front.

As I've said elsewhere, " if you can't afford the petrol,you can't afford a Stagea".

Anyway, racks are not usually an everyday use. The bars take 5 mins to remove. The whole idea was to make something pronto.

As far as agroup buy, The only tools needed are a hacksaw (or angle grinder) to cut the pipe, a 10mm open ender and a Stanley knife, so it is very easy to make. Not really worth the postage.

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339593
Share on other sites
  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...