Jump to content
SAU Community

Recommended Posts

hi there

i'm looking into getting a TD06 20G 8cm for my cefiro - it has a 2.4 RB20 motor in it. currently have a hks 2530 on the car.

I'm after info with people running the TD06 on a rb25 and also rb20 to see if it is suited for my application... supporting mods are - gtr injectors / z32 afm / power fc / full zorst no mufflers/cat with screamer / fmic / fuel pump / pod / bov etc...

this turbo is also internal gate.

PLEASE HELP!

also if i get a good response i may have a hks 2530 for sale located in SA.

thanks

-Matt

Link to comment
https://www.sau.com.au/forums/topic/126750-td06-20g-8cm-on-rb24/
Share on other sites

run for your life.............

heheh just look for another turbo kit, had trouble with the internal gate, it just doesnt work, you will have to custom fit an external gate and blah blah, basically spend $$$$ to achieve anything. cost me 3k to get it working properly

get a 2535 or go garret unless u like the noisy wastegates

Edited by kidd
i've been speaking to a couple people and some have actually said that it may be more responsive than the 2530?

it feels more responsive than the 2530 on normal driving but it depends on what gear youre on, normally had to drop it into second when a 2530 fitted car would only need third to boost up eg when the traffic lights go amber at 60km/h and we cbf stopping :devil:

If you fit an oil cooler i doubt you'll have problems with the engine temperature (assuming your cooling system is in good nick atm).

I think a TD06 with small rear housing on the rb24 will be a bit of a ball tearer to be honest. Obviously less responsive than a 2530 size turbo but not too far behind and a fair bit more top end. I have seen internal gate td05's perform fine so i don't see how the internal gate 6 will have problems.

If you could get your hands on a used 2535 it could be ok . Or since you have the T3 flanged HKS exhaust housing you could buy a Garrett GT2871R in 48 compressor trim - minus the exhaust housing and fit it in your existing HKS exhaust housing . Assuming your 2530 is a Skyline specific one it has the TO4B compressor cover like Garretts GT2871R series uses so externally it would look the same and use the same water/oil/exhaust plumbing and waste gate actuator . The only difference may be the comp cover inlet boss being 3" or 76mm where the HKS 2530 probably had this bit machined off and an adapter bolted on . You could either get this boss turned down in a lathe or use some kind of step down in the inlet plumbing depending on what you car has .

Just in case you didn't know the 2530 and 2535 and all GT2871R series plus a few others use the same identical turbine and bearing housing so the HKS exhaust housing goes bolt . Done the above mentioned way you wind up with virtually a HKS GT-RS but in 48 comp trim instead of 52 trim (better when boost threshold is an issue eg Cu in starved RB20) and without HKS's custom port shrouded comp cover . The 48 trim compressor is less likely to surge than the 52 trim GT-RS but you could get the 2871R's comp cover drilled and slotted so the port shrouding worked TO4Z style if required .

So if you play your cards right this could be a very cost effective upgrade with what is really a brand newin .

Cheers A .

post-9594-1153454992.jpg

They arent a bad turbo, though as someone else suggested the internal wastegate versions do not seem to enjoy the success of the external gate types. I think thats mostly due to the exhaust housing design and subsequent dump pipe the internal gate version has to run.

Here is an external gate version on a completely std RB20.

Dyno_RacePace.jpeg

well i've made 236 previously with stock rb20 / fmic / zorst / 1.3 bar / hks fcd / stock ecu and injectors...

not going to kill myself if i dont get 240 hehe... just a goal. be happier with insane midrange/lower than peak power atm.

cheers roy and like you said can always change it down the track if i want to :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...