Jump to content
SAU Community

Recommended Posts

I am aiming to make my car capable of running flat 14's but have had some conflicting advice on how to do so.

Was wondering if any ppl on here had similar powered cars and if so exactly wat mods u've done to achieve this.

So far I've heard u need:

1:

Full exhast with 2 chambers dump pipe

FMIC

POD

Boost to 9PSI

2: All of above plus Z32 aiflow meter

3:All of above + PowerFC or GREDDY equivalent

Plz keep in mind i dont wanna F$%K my stock turbo so i wanna run 14flat safely without doing any damage

Can ne1 help?

Link to comment
https://www.sau.com.au/forums/topic/127073-14-sec-r33-gts-t/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Full turbo-back exhaust (3inch) - $1000

Replace standard panel filter with a K&N Filter - $100

Bleed valve (10-12psi)- $100

FMIC - $1000

Adjustable exhaust cam gear - $180

= $2,380 + fitting

This should give you up around 180rwkw with a healthy engine. Using decent quality roadworthy standard size tyres (225/50/16) you should be able to do consistent 13.5-14.0 sec with a 1.9-2.0sec 60ft at around 100-103mph, the rest just comes down to driver ability and how long your clutch will last.

Edit: You won't need an Apexi PowerFC, but it certainly would help and you certainly won't need a Z32 AFM (until you change turbo's atleast but by then you will also need a new fuel pump and injectors).

Edited by benm

If you run it at 12psi all day every day you may experience problems but for 14sec a few times every now and then you wont have any problems.

Your clutch will be fine.

Do a search for the Exhaust cam gear, plenty of info available including a thread I created with before and after results.

I did a 13.2 running my car the way how it is:

hardwalled circuit semis. Rock hard coilovers. lowered quite a bit, so too much negative camber affecting traction (-2.5d).

12psi. full exhaust. stainless steel magic cat. No aftermarket ecu.

twin plate clutch with lightened flywheel.

I must admit though, I am really crap at drag racing. If it wasn't for the twin plate, I woulda probably killed the stock clutch in one outing.

PS: I run 12-13 psi all day everyday, and I don't drive it easily. It is still strong after 2 years, and god knows how long or what boost the jap owner ran it on.

I don't see any problem in blowing the stock turbo. They're cheap as chips (around the 3-400 mark for an r33 turbo). I'm happy to blow it and change it myself.

PS: I run 12-13 psi all day everyday, and I don't drive it easily. It is still strong after 2 years, and god knows how long or what boost the jap owner ran it on.

I don't see any problem in blowing the stock turbo. They're cheap as chips (around the 3-400 mark for an r33 turbo). I'm happy to blow it and change it myself.

Yea but u could blow ur engine in the proccess of blowing turbo, i'd be carefull

Mate as you can see in my sig, i have done a 14.04. the car is virtually stock, the mods i have are dump pipe off turbo, 3inch exhaust. thats it really. I run stock turbo, stock FMIC, stock ecu and standard boost. Ohh and that run was on shitty falkens 326's, worst tyre ever!!! well maybe not worst but damn close.

2rismo, I understand that you have extensive experience, and i've been following your progress.

Every car is different. I understand that some cars like benm's was only getting 14s with around 200rwkw. There are others like that.

I can only offer the experience I have from my car. Refer to above. With a catback, pod filter. stock boost. hardwalled circuit semis, I did a 14.01. I have a timeslip at wsid to prove it.

Then with the mods I mentioned above, I did a 13.2. My car is totally not setup at all for drag with the rock hard suspensions, lowered, way too much neg camber. But that's just what my car did. Maybe it's a freak?

I can tell it's definitely the stock turbo, because when I changed the dump, I verified that.

Every car is different. I understand that some cars like benm's was only getting 14s with around 200rwkw. There are others like that.

I call that driver ability, i'm now only doing 12.3sec with a 310+ kw gtr when I should be doing mid 11's.

Edited by benm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...