Jump to content
SAU Community

Recommended Posts

I am aiming to make my car capable of running flat 14's but have had some conflicting advice on how to do so.

Was wondering if any ppl on here had similar powered cars and if so exactly wat mods u've done to achieve this.

So far I've heard u need:

1:

Full exhast with 2 chambers dump pipe

FMIC

POD

Boost to 9PSI

2: All of above plus Z32 aiflow meter

3:All of above + PowerFC or GREDDY equivalent

Plz keep in mind i dont wanna F$%K my stock turbo so i wanna run 14flat safely without doing any damage

Can ne1 help?

Link to comment
https://www.sau.com.au/forums/topic/127073-14-sec-r33-gts-t/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Full turbo-back exhaust (3inch) - $1000

Replace standard panel filter with a K&N Filter - $100

Bleed valve (10-12psi)- $100

FMIC - $1000

Adjustable exhaust cam gear - $180

= $2,380 + fitting

This should give you up around 180rwkw with a healthy engine. Using decent quality roadworthy standard size tyres (225/50/16) you should be able to do consistent 13.5-14.0 sec with a 1.9-2.0sec 60ft at around 100-103mph, the rest just comes down to driver ability and how long your clutch will last.

Edit: You won't need an Apexi PowerFC, but it certainly would help and you certainly won't need a Z32 AFM (until you change turbo's atleast but by then you will also need a new fuel pump and injectors).

Edited by benm

If you run it at 12psi all day every day you may experience problems but for 14sec a few times every now and then you wont have any problems.

Your clutch will be fine.

Do a search for the Exhaust cam gear, plenty of info available including a thread I created with before and after results.

I did a 13.2 running my car the way how it is:

hardwalled circuit semis. Rock hard coilovers. lowered quite a bit, so too much negative camber affecting traction (-2.5d).

12psi. full exhaust. stainless steel magic cat. No aftermarket ecu.

twin plate clutch with lightened flywheel.

I must admit though, I am really crap at drag racing. If it wasn't for the twin plate, I woulda probably killed the stock clutch in one outing.

PS: I run 12-13 psi all day everyday, and I don't drive it easily. It is still strong after 2 years, and god knows how long or what boost the jap owner ran it on.

I don't see any problem in blowing the stock turbo. They're cheap as chips (around the 3-400 mark for an r33 turbo). I'm happy to blow it and change it myself.

PS: I run 12-13 psi all day everyday, and I don't drive it easily. It is still strong after 2 years, and god knows how long or what boost the jap owner ran it on.

I don't see any problem in blowing the stock turbo. They're cheap as chips (around the 3-400 mark for an r33 turbo). I'm happy to blow it and change it myself.

Yea but u could blow ur engine in the proccess of blowing turbo, i'd be carefull

Mate as you can see in my sig, i have done a 14.04. the car is virtually stock, the mods i have are dump pipe off turbo, 3inch exhaust. thats it really. I run stock turbo, stock FMIC, stock ecu and standard boost. Ohh and that run was on shitty falkens 326's, worst tyre ever!!! well maybe not worst but damn close.

2rismo, I understand that you have extensive experience, and i've been following your progress.

Every car is different. I understand that some cars like benm's was only getting 14s with around 200rwkw. There are others like that.

I can only offer the experience I have from my car. Refer to above. With a catback, pod filter. stock boost. hardwalled circuit semis, I did a 14.01. I have a timeslip at wsid to prove it.

Then with the mods I mentioned above, I did a 13.2. My car is totally not setup at all for drag with the rock hard suspensions, lowered, way too much neg camber. But that's just what my car did. Maybe it's a freak?

I can tell it's definitely the stock turbo, because when I changed the dump, I verified that.

Every car is different. I understand that some cars like benm's was only getting 14s with around 200rwkw. There are others like that.

I call that driver ability, i'm now only doing 12.3sec with a 310+ kw gtr when I should be doing mid 11's.

Edited by benm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
    • KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
×
×
  • Create New...