Jump to content
SAU Community

Recommended Posts

Just checking out all the different things on the stag, and found an oil pot thingy in the side panel on the right hand side of the boot area. What is it for?

I was trying to find the rear window wash bottle to fill up, still haven't found it lol

Any ideas on both?

Link to comment
https://www.sau.com.au/forums/topic/127637-found-an-oil-pot-in-the-boot-area/
Share on other sites

The bottle in the rear is your ATTESSA system fluid, (for your 4wd) and the rear washer bottle is the same as the front washer, looking at the enginebay from the front, there should be a yellow cap with a long elongated S shape tube, on the left, near the battery, that is the washer fluid container, well the top of it.

I dunno, but it the car hot/cold? I bet if you check it after driving it around for a bit and then stopping that the levels would be fine, as that fluid is compressd when it is used so the level would drop......?

BUT Then again I really wouldnt have a clue eh, just guessing, wait for Alex or Brad or Gary for an answer from a knowlegable source :)

Thankyou :happy:

With the ATTESSA Fluid, the level is about 1cm over the max line... this can't be good...??

hey kylie thats normal, u gotta check the fluid level with the car ignition turned on and it will drop to the correct level. its just drained back up abit when ignition is off.

cheers

Brad

Edited by CruiseLiner
  • 2 weeks later...

when you guys says its the ATTESA system does it means the transfer case? Cos i want to check every fluid in the car. I dont trust those Kamilaze guys.

First of all the didnt fill the coolant resovoir tanks. Engine oi is fine. Power sterring fluid is over filled i check it when its cold. I want to check the transfer case, gerbox and the diffs. Does it means that i have to jack the whole car up and also the car is so damn low

Ah sorry mate, the reservoir in the boot is just for the Attessa pump system, which pressurises the clutch pack in the transfer case. The transfer case oil is separate.

Ok so what kind of oild does it use? Gearbox oil? hydralic oil? or diffs oil?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...