Jump to content
SAU Community

Recommended Posts

ok went to put on my fantastic new SAU stickers this morning...

but to my suprise when I went to take off the tape the backing didn't come off the tape on the front did...form my experience the backing usually comes off and you stick them on the window and then slowly peal off the front tape...LOL I was upset and didn't bother with the other one.

Am I doing this right? my car is naked now cos I took off the old stickers !!

Link to comment
https://www.sau.com.au/forums/topic/130058-sau-stickers/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

was there a bad batch?? Guess so...dunno how to fit this and make them look nice if I do each one by itself...

i dont know if it was a bad batch, but they all seem to be like that.

i got paul's gf to do mine, and she had to pick each letter off 1 by 1 and do it that way....

Link to comment
https://www.sau.com.au/forums/topic/130058-sau-stickers/#findComment-2405836
Share on other sites

i dont know if it was a bad batch, but they all seem to be like that.

i got paul's gf to do mine, and she had to pick each letter off 1 by 1 and do it that way....

hi, that would be me.

ive put on at least 8 of those stickers now (on 4 different cars) and have always done it fine, no fuss, no muss.

every sticker is different just be patient, id say

and no i didnt have to peel off every letter at a time for them

Link to comment
https://www.sau.com.au/forums/topic/130058-sau-stickers/#findComment-2405916
Share on other sites

Chris...

Mate i had some trouble with mine when i first put them on i was rushing it...

Also another thing make sure the window is clean.. Something that can be overlooked but if the window is covered in crap the sticker wont stick anywhere near as well as it should...

Link to comment
https://www.sau.com.au/forums/topic/130058-sau-stickers/#findComment-2405925
Share on other sites

You assuming things again arent you?

Where did i take mention to Sarah, who hasnt even posted in thier farken thread.

lol ok ash. if you're going to nit pick at every post of mine, good luck.

I asked a question, hence the "?"

Because as khunjeng stated, the SAU stickers do not work the way other stickers with a backing sheet do.

Sarah put mine on fine, but she still didnt do it the way stickers with a backing sheet are supposed to work

Link to comment
https://www.sau.com.au/forums/topic/130058-sau-stickers/#findComment-2405931
Share on other sites

I bought some for SKOOB and they went on no problem however the ones I got for the Evo were a nightmare. Trying to place the dot on the i was the hardest. There was about 12 months between them. I got a URL at the same time as SKOOB's ones and only just put that on the Evo and that also went on fine.

Link to comment
https://www.sau.com.au/forums/topic/130058-sau-stickers/#findComment-2405957
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...