Jump to content
SAU Community

Rx7 Injectors In Rb25? Or Similar

Evasion

By Evasion,
in Engines & Forced Induction

 Share

Recommended Posts

Evasion Explorer

Evasion

Posted
Posted

Hi

I'm putting this up for a mate he has a r33 rb25det. now at the moment hes running out fo fuel due to stock injectors, has power fc supporting mods blah blah blah.

Now I know that s15 injectors fit into the rb25, some people on here prob use them think there 440cc.

But one thing from memory is that people with s13/14/15 can use rx7 injectors as they fit the sr and provide an extra gain going to 550cc, so my question is.

Can the rx7 injectors (550cc) work on a rb25det, do they have the same impedence, or is there another cheapish upgrade out there

Any help muchly appreciated,

Thanks all

Link to comment
https://www.sau.com.au/forums/topic/130505-rx7-injectors-in-rb25-or-similar/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

yeah ive read you can use rx7 injectors which are 550cc (ish)

but youll need to find 6 of them of course. its probably easier and cheaper to just buy a set of 6 injectors instead of 4 and then 2. also s15 manual jdm injectors are in the similiar boat, but are 480cc.

darrinspencer Grand Master

darrinspencer

Posted
Posted

You need the series 6 "primary" injectors from memory

The secondary injectors are higher flow again

Since there is only 2 primary injectors in a 13B, you need to find 3 sets, which is not easy

I think the WRX boys want them too

I went thru this a while ago, and ended up getting S15 injectors

There has been much debate whether they are 440/448 or 480cc

On NS.com, the majority say they are the lower 440cc, not the 480cc

The Dan Grand Master

The Dan

Posted
Posted

Do half a job and you will get half as good a result.

RX7 injectors are very unreliable. Especially the S4/5 ones. They only operate effectively to a duty cycle of 60%.

A set of sard 550cc injectors you can get for $750 delivered to your door. Why would you mess around with anything less?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...