Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i sat there for a good 2-3 minutes re-reading your post.. then i realised it was the *other* sam... i was wondering why you were aksing what '235' meant, when you were telling us before.. :D

the '235' etc, is the tyre width.

normally a tyre will be given a code (im not entirely sure what to call it actually), but it will looks something like this..

235/45R17

what that means, its a 235mm wide tyre, with a 45 profile rating, and it suits a 17" rim.

now the width is obvious the width of tyre that touches the road, the wider the tyre, generally the more grip you will have, but it will cost more, and you need wider rims to get really fat tyres onto them.

the 17" part is pretty easy aswell.. 17" rims uses 17" tyres.. got that? :stupid:

the profile part is a bit of a prick.. what the '45 profile' means the sidewall is 45% of the width of the tyre..

so the sidewall on this particular tyre is 235 * 0.45 == 105.75mm high.

this by itself typically doesnt mean alot.. but it helps when you run different width tyres on the car (ie, you may have fatter on the rear.. like myself, and many others do)

say i want to use a 255 on the rear.. i need to find a 255 tyre that will have the same sidewall height as a 235 tyre, so to do that, i get 105.75 / 255 == 0.414, so approx '40 profile' is needed, meaning you need to use a 255/40R17 to obtain the same rolling diamter as the 235...

now that you are probably well and truely confused, i think my job is done. :laugh:

All you need was a picture for the perfect explanation :no:

ns-wheelradius.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...