Jump to content
SAU Community

Brake Pads For Sprints And Road

260DET

By 260DET,
in Motorsport Discussion & Builds

 Share

Recommended Posts

abcent Mentor

abcent

Posted
Posted

maybe the Ferodo DS3500? but i've heard there not very good road pads. You'd be the first i've heard that wasn't impressed with the 2500's though.

Apparently Prodjuct Mu pads are good, but again, only going on what I've read around the place on here.

theres RaceBrakes RB74's that alot of people use an recomend but say once over heated once there not real crash hot?

check out www.nismo.com.au too, they have a few options with brake pads an different temp ranges

hope this has been of some help, Cheers

Berin

boxheadmr Mentor

boxheadmr

Posted
Posted

I too am surprised about the comments with the DS2500's???

Due to current brake set up i am using endless NA-R's which i have found to hold up quiet well. They warm up quiet quick and will hold on for quiet some time before getting some ever so slight fade but usally only after 15min full pelt around the track. They would be a good pad for super sprint and then drive home on them road use.

ferni Grand Master

ferni

Posted
Posted

I've swapped from RB74 to DS3000, found the DS3000 much better so far (but thats what i was expecting). I have also used the DS2500's on the M3 Driver training day, they run them in thier driver training cars on the track at philip island, they coped a beating all day, lap after lap for like 20-30 laps at a time with no fade or problems.... maybe the 2500's you had were fake or a dud set? find it hard to belive the bendix stuff was better.

tacker Mentor

tacker

Posted
Posted

Yep i have the project Mu level 900 on the front bendix ultima on rear, nismo steel braided lines, standard gtr calipers and RDA slotted standard size rotors and lots and lots of brake ducts.

I can get through a 20 minute track session with just the smallest amount of fade, pedal drops about 20mm. And the ambient temp was 40 C +.

BUT they dont come cheap.

  • 2 weeks later...
Duncan Grand Master

Duncan

Posted
Posted

well.....hawk black = race pads = not for road use.

Thats how I see it, I am happy with their performance for race use, been using them all year, they seem better than the SBS pads I used before that. But race pads is a different topic I think.

  • 3 months later...
JZX91-2JZ Enthusiast

JZX91-2JZ

Posted
Posted (edited)

As a street/track pad my only experience has been with Ferodo DS2000 and have dfound them to be very good, but it has been my only experience.

PS-Sorry to bump something a few months old

Edited by JZX91-2JZ
Belsil80 Mentor

Belsil80

Posted
Posted

I have project Mu pads and rotors on the front, they take a while to get up to temp, and are average when they are cold, but on the track they are great! I have only had the slightest brake fade, and that is after a lot of 200kmh stops.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...