Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

my xr6 turbo has a stock gt35/40 turbo. even though its running only 5.6psi of boost, and has a 4l 6 cylinder engine, and it doesn't lag one bit.

however on an r33 with only basic mods i think you will find there to be quite alot of lag if you want to run higher boost levels.

"The GT3540R core swap is about a 6 hour job, where adaptors plates need to be welded and machined and tapped to the turbine housing, and some extensive machining and modification is required.

The GT35R Conversion - Rated between 600 & 650 using customers housings.

Well thank you for clearing it up.

Now please extrapolate on how it spools..........

A 'real' GT35r .7 comp .63 turbine I would expect to be all in by 4000 on an rb25. How does yours compare?

Well thank you for clearing it up.

Now please extrapolate on how it spools..........

A 'real' GT35r .7 comp .63 turbine I would expect to be all in by 4000 on an rb25. How does yours compare?

Yeh i would say u be just about spot on with all hell breaking lose at 4000rpm. Needs to have full tune in 1000km's time and then i will be increasing boost to see what it can pull. Yeh guys that built motor were quite surprised at its response. They thought it would be much laggier (pulled 187rwkw's @ 3-4psi on a dyno run done while they were giving it a mild tune and bedding rings - running stock injectors and gtr pump + fuel reg)

Will post up a dyno chart for sure once its been fully tuned and boosted.

Edited by FSTR32

So its 3-4psi @ 4000rpm?

Dont know how hell breaks loose when its really not even doing anything

I think once more boost is put in you'll find that it wont actually be the same as 3-4psi that you have now

So its 3-4psi @ 4000rpm?

Dont know how hell breaks loose when its really not even doing anything

I think once more boost is put in you'll find that it wont actually be the same as 3-4psi that you have now

No its running 8psi at the moment and yeh its doing plently...doesnt throw you back in ur seat but its more of a consistant build up which is why it feels like it has no lag at all We'll see how it goes with a bit more boost but want to change injectors and fuel pump before that.

Consider the GT3540 .63? I'm sure SAU needs a guineepig. ;)

Looks like it has already been done....

http://www.skylinesaustralia.com/forums/in...110&hl=gt35

~ 450 hp @ 17psi

~ 480 hp @ 19psi

Not sure about response as no graphs as yet.

Cheers.

I'd be looking real close at the GT35R/GT3582R turbine map and note the total mass flow .

There are some GT35R "Hi Flows" getting around but not my whissle to blow . Search GCG or Full Race Motorsport in US under GT3567R . HKS is supposed to have an experimental version of the GT35R as well .

Just as food for thought , I've been told that even std GT35R's can bend turbine shafts if pushed really hard . Using greater capacity (and diametre) compressors is not going to improve reliability . The TO4Z uses the larger shaft (and bearing pack) which survives pretty well and is the same effective guts as larger GT37R/40R/42R/T51R etc . People need to realise that the GT35R is as large in the wheels department as the basic GT25BB centre section gets , in fact the compressor end part of the shaft is a little larger than most GT25BB turbine shafts .

My ideas only but the GT35R would have been better with a smaller trim compressor like the HKS only GT3040R or GT3240R uses . Better to give the turbine less load to push against than to speed up the exhaust gasses (via smaller AR housing passages) which limits total exhaust flow .

Someone else mentioned a TO4 Hi Flowed with a GT35R cartridge . This has been done in the US and gets you a TO4 exhaust housing instead of Garretts native GT35 housings . Possibly reprofiled TO4 "O" trim housings . Depending on what comp cover the "TO4" had it could be profile machined to suit the 82mm GT40 compressor . There is a cover that suits the TO4E backplate already so machined .

Someone mentioned the GT3071R , this med sized animal can churn on paper ~ 440Hp worth of air - provided the engine is modified and tuned to do it properly . At least its turbine and compressor are large trim (84 and 56) and the wheel diametre ratio is good . You could look at it as a GT2835 with a smidge more turbine because thats what it is .

Cheers A .

My guess is not tuned properly or non genuine turbo or screwed engine. I run 0.82 on my stock fj20 at it sees 10psi at about 2500rpm and full boost at ~4500 as mentioned before. Ive seen an rb25 on the same dyno as mine (pits matt spry) with 3540 0.82 and by 4000rpm on had 14 psi adn was beautiful to drive, though not a gcg highflow...but much more powerful.

had a GT3540 0.82 on a standard RB25 with fuel support mods only and Link ECU.

12psi boost by 4900 rpm. Very laggy on the road. Horrible to drive with on/off power extremes.

yuch

Mike

Is the numbers your quoting on a dyno or on the street?

There is a massive difference between loading a car up on a dyno and getting boost to come in super early in 4th...

As opposed to 60-140km/h say on the street which see's an un-loaded 2nd and semi-3rd.

On the street a .82 GT35 i would fully expect to be in around 4700-5000rpm

Shit me, I find the 3540's laggy on xr6T with all the mods and remember they have indepandant cam timing (on the BF's). Thats not including the nizpro intake manifold casue its awesome for response. Its going to be laggy as hell on a 25. I would think 12psi by 5000rpm at the earliest.

My guess is not tuned properly or non genuine turbo or screwed engine. I run 0.82 on my stock fj20 at it sees 10psi at about 2500rpm and full boost at ~4500 as mentioned before. Ive seen an rb25 on the same dyno as mine (pits matt spry) with 3540 0.82 and by 4000rpm on had 14 psi adn was beautiful to drive, though not a gcg highflow...but much more powerful.

Thats pretty awesome response, almost unbelievable as a mates S15 I drove didn't even spool that well on the stock turbo. :P

Even on the RB30DET's you only see 5psi by 3000rpm and then ~3600rpm or so what ever boost you throw at it.

But then again boost is a measure of inlet restriction.

Shit me, I find the 3540's laggy on xr6T with all the mods and remember they have indepandant cam timing (on the BF's). Thats not including the nizpro intake manifold casue its awesome for response. Its going to be laggy as hell on a 25. I would think 12psi by 5000rpm at the earliest.

its no where near that...as I said before my 3540 hits 15psi at 4600rpm. 12psi at 4250rpm, and thats with the .82exh housing.

On dyno and street in 4th . To tell you the truth, I dont really know when it comes in by on the street in the first 3 gears, i dont have time to see as it just flies through the revs so thats why i only know in 4th gear. Apologies to those who were confused. I will mention quoted figures are in fourth :D

But the person wants to know whether its big lag, I dont think so. Its laggy, but not big laggy and its nice* to drive on the street bt 2-3000rpm.

*Nice may not be nice to you :)

Is the numbers your quoting on a dyno or on the street?

There is a massive difference between loading a car up on a dyno and getting boost to come in super early in 4th...

As opposed to 60-140km/h say on the street which see's an un-loaded 2nd and semi-3rd.

On the street a .82 GT35 i would fully expect to be in around 4700-5000rpm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...