Jump to content
SAU Community

Recommended Posts

Only just got my GTR back from the workshop with the new addition of forged pistons and still have 500 k's before im over the safe 1000. Only been boostin it to 4000 just to run it in. It has N1's which start spooling at 2500 so it still puts you back but every now and then it feels like it doesn't want to boost. Im thinking its something to do with the turbos?? Don't know much cause the last turbo i had was in a 1 litre charade and that was only to give it enough power to get up the hills :)

Link to comment
https://www.sau.com.au/forums/topic/132706-lag/
Share on other sites

You on a standard tune, could be boost cutting as it hits 4000rpm if you've upped the boost from standard without remapping the ECU and removing all that business.

If they start spooling at 2500 youd be near full boost by 4000rpm i would think... or is it immediately after they start boosting?

In which case I'd check for things like leaks, wastegate, disconnected lines etc.

Can you be a bit more specific, does it surge, or just plateau out, or cut out all together in terms of boost when you say "it doesnt want to boost"

Link to comment
https://www.sau.com.au/forums/topic/132706-lag/#findComment-2458781
Share on other sites

what boost are you running, and what is controlling the boost? if you have a boost controller then it may be slightly blocked and not releasing the air between it and the wastegate, so when you try to accelerate the wastegate is still open and it won't spool up properly.

Link to comment
https://www.sau.com.au/forums/topic/132706-lag/#findComment-2460155
Share on other sites

I've talked to my mechanic about it and he reckon's its the coil pack without looking at it. He said the first time he started it up it was only running on 5 cylinders then after a couple of minutes the 6th picked up. Thinking about it, it makes sense if its a firing problem. I said it was 'every now and then' and most of the other time it's great. At 4000 it doesn't feel like it going to run out of boost!!

Link to comment
https://www.sau.com.au/forums/topic/132706-lag/#findComment-2475346
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
×
×
  • Create New...