Jump to content
SAU Community

Recommended Posts

Hi Guys,

Im trying to install an Xtreme Lightweight flywheel on my RB20DET A31 and I cannot seem to get the flywheel on! Ive done some quick measurements and the Outside of the crank is about 36mm and the internal diametre of the flywheel is about 35.25-35.50mm - the factory flywheel is about the same as the Xtreme. Im using those caliper thingies and they definately have to extend after measuring the flywheel to fit over the crank.

Am I missing something here or is the fly too small to fit over the crank? I know it should be tight but is there a trick I can use? Ive tried sitting the flywheel just over the crank and hitting a piece of wood on the flywheel to get an even fit but it wont budge. Ive also tried a little lubrication but to no avail.

I had thought about installing all 6 flybolts and tightening them evenly to get it to "press over" the crank but If its not gunna go then I can see me crossthreading something and I would hate for that to happen!

Thanks!

JK

Link to comment
https://www.sau.com.au/forums/topic/132715-cant-install-flywheel-crank-too-big/
Share on other sites

Couple of options from one backyard mechanic to another.

1. Put your flywheel on your BBQ on low heat for 10min, then with some heavy duty gloves try to install quickly. The heat should grow the flywheel by just enough. I have done this before when shifting ring gear (the bit the starter turns) from one flywheel to another and it works a treat. I know it sounds a bit redneck, but this should work. Alternative is an oxy torch to heat it up, but can be hard to get an even heat with an oxy.

2. The press method with the flywheel botls 1/2 turn at a time should work. Just take it easy.

I'd say heating it would be the way to go thou. Hope that helps.

But it has to come off some time Chris so I don't recommend it. Talk to the supplier and check the dimensions, my suggesdtion is it didn't get checked at manufacture. It shouldn't be an interference fit but a sliding fit. A machine shop or engine builder should be able to quickly take it out to the right dimension

I have been contemplating getting 40tho taken off from the inside of the flywheel - BUT i tried to get the factory flywheel back on today and it wont go back on either... how bizzare.

My crank has grown haha

JK

I also noticed that the factory flywheel has some extra machining done on the inside whereas the xtreme doesnt.

So it should be safe to take material off the inside of the flywheel? It should still bolt up OK and should still be "hub centric" over the crank but it wont be tight as buggery like it is now.

JK

if it is the alum one i just left mine in the sun for 30min and it went straight on. to get it back off u just heat it back up.. easy!!

alum expands at diff rates to steel so i wouldnt machine it

hmm I dunno if i'd go machineing it, unless you can confirm your crank is actually bigger than stock. Plus it will be under heat cycles because of the fact it is a friction surface item.

Let's say you take a bit out of it, then it will fit on nicely while cold. But the flywheel expands at a different heat rate to the crank... I dunno perhaps then it may not run 100% true. Just chuck it on the Bar-by and cook yourself up a flywheel with sauce, slide it on and bolt it up. I'd go for tight fit anyday!! (no sexual inuendo intended of course)

I called Xtreme and they recommended heating it aswell. I will give that a go before looking at machining it. I'll have to use the gas stove top inside to do it (whilst the missus is out haha)

JK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...