Jump to content
SAU Community

Recommended Posts

I bought an r32 gtr diff , shafts and hubs of a friend who originally pulled em out of a r32 gtr wreck

my car is early 89 gtr and has a finned cover, this one doesnt have finns has anyone seen a 32gtr rear diff with no fins?? oh yeah its a white one so im thinking a later model 32

also the non finned cover is 31 spline. finned is 30 spline

thanx T04GTR for the info

so are the 31 splines on the pinion or the side gears?, the diff has the input flange and output shafts still in it will I need to change any thing to fit the late model diff.

keith

finned cover is vspec diff

man i get tired of people misquoting info on 32 GTR diffs! I must hear it about once a month. as my man dave has pointed out ALL pre-model update BNR32 GTRs have a finned diff cover. later models have the plain cover.

swap to the finned cover. it holds more oil.

thanx again

this is all good news Ive scored a late model diff and i can put the best bits on it [finned cover]

and sell the leftover drive shafts and stuff, my lsd centre will be okay for some one too if they have a quiet set of gears.

man i get tired of people misquoting info on 32 GTR diffs! I must hear it about once a month. as my man dave has pointed out ALL pre-model update BNR32 GTRs have a finned diff cover. later models have the plain cover.

im sure paulr33 was thinking of r33[he has got a huge thread on r33 vspec active lsds]

i did a fair bit of searching on diffs in the drivetrain thread but didnt come up with the answer but i did find heaps of misquoted info that i had to sift through, but hey in any forum you have to dig to find gold

werd :)

ps.. your driveshaft flanges that you are gonna chuck are gold.

ps. any aftermarket mechanicl lsd needs these flanges for them. pitty there 6 bolt lol.

r34gtt helical uses them to i think.

hey to4

are you saying all aftermarket centres use 30 spline side flanges?

are they hard to get because they break a lot or is it because ppl do gtr upgrades?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...