Jump to content
SAU Community

What Have I Done!

Jsikalias

By Jsikalias,
in Engines & Forced Induction

 Share

Recommended Posts

Jsikalias Rising Star

Jsikalias

Posted
Posted

hey guys,

tonight i was driving down the freeway in 3rd and noticed as soon as i put the foot down to change to 4th gear my engine light flashed and then didnt come on again.... i have a stock r34 only mod is a catbak zorst, wat does it mean when the engine light comes on? the car felt normal though it didnt sound like it was missfiring or boost cutting... any help will be appreciated thanks

Link to comment
https://www.sau.com.au/forums/topic/133889-what-have-i-done/
Share on other sites
shif_tea Grand Master

shif_tea

Posted
Posted

you can check the ecu to see what the fault was. I'm not sure how its done with r34s but someone else might know. Might be the same as for r33's, if so, search it cause its been posted a few times. If you take it to nissan they can check it with datalogic and see whats the problem. Could be nothing...

700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

Hello,

More than likely it is O2 sensor, this happend to me once.

But do a check.

The mechanic at the time bridged some point up with a wire and the dash lit up several times to

notify us of the fault and which sensor it was.

I am not sure if this is the same for R34's. :)

wilch Grand Master

wilch

Posted
Posted
i think i need to take it for a tune?

congrats on finding a PFC where your standard ecu should be :ermm:.

Yep, get a touch up tune just to make sure everything is ok.

With a PFC the check engine light generally flashes if the knock reads >60. I'm guessing it knocked a little when you floored it and put the engine under load a little. Just get a touch up dyno tune done :P.

lanky71 Veteran

lanky71

Posted
Posted

I had this problem when I first picked up my r34 turbo from the dealer.

He did the diagnostic and it turns out it was a speed controller. He said just keep driving it till the part comes in... Then 3 weeks later the warning light switched off and no problem since... Though I have had the speed controller replaced just in case but it is amazing what sorts of warnings this advanced electronic controlled cars can give you.

Battery was out of the car for one week whilst a body kit was installed, then the driving to work on the F3 in Sydney to Gosford car turns off and does some sort of emergency breaking, turns out one of the battery cells had died and was only causing a fault occassionally when more then normal power was being consumed. Naturally this was a wet day, so had headlights, wipers, stereo and the driving aids were occassionally kicking in.

Anyway, moral of the long and pointless post :ermm:

Find yourself a good "import shop" that you can build a relationship with so that you can have problems solved easily and without being ripped off or car damaged by a mechanic who does not work with imports.

Also just incase you didn't know where your diagnostic plug is, it is below the steering wheel to the right it has a little latch where you can unplug it and then plug it in to a diagnostic tool or workshop... or even one of these great new toys from greddy I seen in the latest high performance import magazine.

Drew.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • dawhitehonky
      M35 Aftermarket Fuel Pump

      By dawhitehonky · Posted

      I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • GTSBoy
      Rapid-fire squeaking/creaking from rear suspension

      By GTSBoy · Posted

      Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...