Jump to content
SAU Community

Recommended Posts

Hi all.

So i know what each is, but how do i dignose it. I keep thinking i keep on hearing things in my R33.

How does one tell if the engine is knocking or pinging. I have fitted an SAFC II and i hardly get any knock maybe up to 15 or so. The car pulls HARD and EAVEN all the time, but somethimes i swear to god i am hearing something like knocking or pinging, but the car does not stumble or anything, no missing, no smike nothing. ( hard to tell with 3.5' exhaust and HKS pod)

So how does one tell by ear if anything is happening. What noises can you tell from, and symptoms.

ALSO how do i check timming, i have a series 1.5 so a series 2 ignitor on coil, no idea how to connect things up.

What are the timing setting suppose to be at idel ect????

HELP ME FROM GOING INSANE

Edited by WogsRus
Link to comment
https://www.sau.com.au/forums/topic/134153-knocking-and-pinging/
Share on other sites

Knocking and pinging is generally caused by improper combustion in your engine, called "auto-ignition."

An internal combustion engine runs properly when the spark-initiated combustion wave expands rapidly but smoothly across the combustion chamber.

If the gasoline-air mixture auto-ignites somewhere in the cylinder (other than at the spark plug) just after spark ignition, the auto-ignition combustion wave can interact with the spark-initiated combustion wave, causing the vibration we hear as a knock or ping.

Increasing engine load, temperature, compression, spark-advance, air-fuel ratio, combustion chamber deposits, and decreasing altitude all increase the tendency for an engine to knock. :(

if your car is pinging/knocking its not good. Its something you should get checked out man. the human ear cannot hear about the first 10% of the sound that is made so if you can hear it over the exhaust pod than its pretty bad. If you got a Power FC I think there's a function where you can make it flash the engine light when its pinging/knocking???? Good luck man.

well the car is runnign stock boost and intercooler but new pod and exhaust, i am not saying my car does knock or ping, i simply WANT TO KNOW what they sound like and how to pick it ip if it does do it.

SO SOMONE tell me please.

I know what they are and what happens to the engine when it goes wrong, but HOW do it pick it up by ear.

THANKS.

BTW My safc II has a knock setting, it never goes higher then 15 or so.

Edited by WogsRus

If u can hear it pinging will sound like a box of matches ratling in the background very faint, then sever knocking is basically that, like a cylinder went knock on the side, well thats my interpretation. I drove around for 2 days wihtthe pining box of matches sound and it was real quiet so i thought it wasnt to big a deal to be urgent and then i busted a piston. ended up buying a new engine. Get it checked if your in doubt by a good workshop.

Thats my point, i have a 3.5" ehayst and a HKS pod with bellmoth intake, and at 4000rpm, no idea what is what, everything makes noise.

I have a timing light now and will check the timing this weekend.

Will pinging be notice by performance, ie losst or a miss or something

Listen to a loaded up mitsubishi express van go past in a gear too low for it. That's pinging. It's a metallic kind of rattling. I can hear it in my car but my exhaust isn't that loud and I don't have a pod. It's easier to hear with the windows up.

It's the kind of sound that someone needs to point out to you. Once you know it you know it. Hard to describe otherwise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
    • They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
×
×
  • Create New...