Jump to content
SAU Community

Recommended Posts

well you can get pretty much anything landed in Aus for 10k, but when I did this I found I spent 10k on the car and 20k on the prep not the other way around.

consider cost of

cage

suspension (whatever it has will be too tired)

saftey stuff - extinguishers, tow hooks, kill switches, fuel pump cut, window nets, tailshaft loop

seats & harnesses

wheels and tyres

all new bushes, let alone rose joints or adjustable arms

guages

ecu and tuning

new pads and discs, overhaul calipers.

reco all CV joints (4 on a gtr), tie rod ends, 4x wheel bearings, tail shaft unijoint.

reco starter and alternator

replace all hoses and belts......over 30 hoses on a gtr

all new fluids - coolant, engine oil, gearbox oil, diff oil (x2 gtr), transfer case, attesa fluid, power steer fluid, brake fluid

replacing anything else that is worn out or broken

and hopefully the motor and compression is OK.

only after all that would you have a safe starting point to make something go faster....

I know that I could do the other war around, but I was hoping for a early 1990's GT car that has already had a lot of money spent on cages, seats, gauges, suspension and the rest of it.

My understanding it the cage will be compliant as they follow FIA regulations, so it should have a FIA approval, as will the seats and harnesses.

It may be a pie in the sky idea that I can get a fully setup car, but from the prices I see for import drag/drift prepped cars, I think there would be pleanty of tarmac cars waiting for a good home.

Rather then look at buying out of Japan, you shoudl also consider buying a prepared car out of Europe. Some good buys going around. Right now im tossing up a track only GTSt, what will stop me is my trip OS and the procurement of one of these

cb_1.JPG

:):P;):D

My budget is $20k for a full race spec car. I do not think I am unrealistic in my expectations. I think that a race prepped RWD car from japan could easily be aquired for that money. I have a further $10k to spend on spares and anything that needs fixing.

I have also seen EVO6's going in race trim (rally) for $20k FOB.

Seriously on that budget go buy a 125cc Kart and have some fast fun...I have brought in plenty of race car s from Japan and there is lots to be spent when all is fixed and made safe....i think you may be disappointed with what you end up with on a 20k budget....my current club sprint GTR which was 800000 Yen and loaded with all sorts of goodies now owes me over 50k after 2 years of development/tuning/extra safety gear/slicks etc

I tried a 250cc international superKart, but it was too hard on my back, but the most fun I have ever had on a track. I would prefer to have pannels and a roll cage around me when doing high speed.

I understand that there will need to be money spent, I own a business that will be sponsoring it. I am realistic about costs of owning a car, as I have owned 2 sports sedans many years ago.

I do not see why I cannot pickup a fully race RWD car from japan for my budget that will be fine for club work. I do not intend to do any national series, only private days and supersprints.

Does anyone have any websites that advertise these types of cars ?

Edited by 4DoorGTR
Rather then look at buying out of Japan, you shoudl also consider buying a prepared car out of Europe. Some good buys going around. Right now im tossing up a track only GTSt, what will stop me is my trip OS and the procurement of one of these

cb_1.JPG

:);) ;) :)

Wanna bring me one back too Troy?? :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...