Jump to content
SAU Community

Recommended Posts

hey mate, i have done it on a N/a 4cyl , i wouldnt recommend it for a n/a car and i wouldnt do it on my r33.

i doubt there is much performance ot be had with a street r33 any ways ?? is there?? it would be very minimal if u had a dump full zorst and a high flow cat alrady.

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2505374
Share on other sites

Hey guys,

I am aware of punching the center out of a cat is illegal . Im thinking of punching out the inards of my sports cat and replacing it with a 3 inch pipe.

Anybody got any ideas and comments on the matter?

not sure what info your after. you admit you know that its illegal, thats really all there is to it

theres very limited gains to be had

i had one on my 33 T when i first got it

replaced it and felt or saw no difference on the dyno

a very slight deeper note to the exhaust and a little more stinky thats the only differecne between that and a god quality hi flo item

Jimbo

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2505383
Share on other sites

if you are in qld you will just have to watch out for the hoon squad. when they are doing a blitz they have a epa station setup and they will tell you to go straight to it and escort you there. they did 1 up here in gympie. had it setup for emisions and noise. went right over the car.

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2505525
Share on other sites

lol i saw "cat punching" and the last post by ctjet, it made me think of something entirely different.

I think the noise must depend on the car. A couple of my mates have had theres hollowed out and it sounds sh!t.

Personally I would just get a high-flow.

Edited by shyster
Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2505533
Share on other sites

When my old S13 was brought into the country, the CAT had been split at the top - gutted out - exhaust went straight through - and finally the cat sat back around the exhaust and welded at the top where no one could see.

Sensor was still sitting in it - though it was ummm loose and rattled..lol

Went to replace it but when I took it over the pits at the RTA for first rego they didnt even test it!

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2505971
Share on other sites

The RSPCA will be onto you pretty quick for punching your cat.

PS think about what it does to the environment, and whether you are that selfish to do it for the maybe 5kW extra. Just go buy a good new metal substrate cat.

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2506028
Share on other sites

Hey guys,

I am aware of punching the center out of a cat is illegal.

Anybody got any ideas and comments on the matter?

Yeah, I do believe that punching the innards of a cat is illegal. But I don't know, I much prefer punching cats in the face.

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2506572
Share on other sites

knocking the car isnt the bet idea

best to get a pipe.

have a look at it all, the exhaust gas would be mising around something shocking, so possible gain... but a better gain from a straight pipe thats evenly flowing

Link to comment
https://www.sau.com.au/forums/topic/134803-cat-punching/#findComment-2507422
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Absolutely could be. I collected data logs from when the O2 sensor was still out and also after I had replaced it so will try to compare them. Pretty confident that the affect is lowered with the new sensor, will check logs at the same RPMs/conditions. 
    • Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
    • Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
×
×
  • Create New...