Jump to content
SAU Community

Stock gts intercooler/performance


Recommended Posts

Guest skybound

im kinda new in terms of turbo cars and have just purchased an r33.... sorry if these questions are lame! but is a stock r33 intercooler any good or should i get it changed - also what should i first start to add or change on my car to improve its performance.. basic stuff to start :D

Link to comment
https://www.sau.com.au/forums/topic/13562-stock-gts-intercoolerperformance/
Share on other sites

Hi Skybound,

The stock intercooler is not much good at above factory boost, so if your after performance then a front mount intercooler(FMIC) is a must.

The first thing is to replace the factory exhaust system, a full exhaust from the turbo back is best. Then things like increase the boost, pod filter etc.

See'ya:burnout:

I agree with shuto-boy, you don't need huge-ass intercoolers, since you'll experienCe l ag if it's too big

and as paul said, don't bother yoursElf with the branded intercoolers as thats just an extra 1ooo bux on the price

juSt go a suitably sized (for thE amount of power) custom core, frOm a tRuck or whatever, and get that put in

welcoMe you too btw as well :)

p.s - cAn you please buy mE a nEw keyboard while yOu're out???? thIs o ne is ROOTED!!

Did someone say intercoolers?:)

Stock intercooler is a BAD place to start modifications.

It offers very poor value for money when you are chasing 'the basics' and specially with only the stock turbo.

If you have a budget of $3k or less leave it alone for now, and just make sure you have the other bases covered first.

Unless of course you are made of money (New turbo's?) or like losing to much less modified skylines in races.:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...