Jump to content
SAU Community

Recommended Posts

Thought I might open this up with a list of mods, wont put in a future list coz I don't think the page is big enough :laugh:

Bought the car with Pod, Teins, Nardi, 16in AVS, Newly transplanted Rb20 ('uknown' k's), blitz boost gauge and around 160,000k's on the clock. Now it has the following mods and ~208,000k's on it:

  • Apex Pod (Replaced the K&N oily one that came with the car)
  • 40mm Alloy Rad
  • Uras Bodykit (Now sold and back to standard)
  • HKS Oil Cooler
  • Rainbow Sox
  • Extreme HD Clutch
  • Bleed valve @ 0.8Bar
  • Bride Zeta
  • Reinhard Catback
  • Speco Water temp gauge (soon the be replaced with Defi Din gauges)
  • Kaaz 2 way diff

Here are some pics. will get more when its lighter, stupid video cam takes shitty stills in low light.

post-18824-1159173438.jpg

Interior when I bought the car.

post-18824-1159173495.jpg

Engine bay prior to 40mm Rad going in.

post-18824-1159315520.jpg

With 40mm Rad.

post-18824-1159173464.jpg post-18824-1159173998.jpg post-18824-1159174178.jpg

With Uras attached.

post-18824-1159173354.jpg

Bride Zeta.

post-18824-1159173201.jpg post-18824-1159173242.jpg post-18824-1159173274.jpg

Reinhard. Complete with removable mufflers and silencers (excellent for street use).

Here is a vid of my drifting with the exhaust fitted:

That's all for now. Konect.

Edited by konect
Link to comment
https://www.sau.com.au/forums/topic/136000-konect-1990-cefiro/
Share on other sites

NICE VID!

what is the tune like on it? sounds a bit laggy? love the RB sound though!!

Nah probly more my driving that makes it laggy. Was my first run for the night so I was a bit out of practice, later on I started keeping the revs up while on handbrake so it wouldn't bog down, then slamming third for the last corner.

Tune is the normal jap tune (rich as a mofo!) and comes on about 2.5k revs which is about normal. Not too bad to drive :)

Thanks for the comments :yes: Will get better footage next month.

nice car mate, it reminds me of the one in bigx in hpi9 (except yours is better), i cried when i saw what they did to that car :nuke: ..... and the laurel :):)

lol yeh i have that vid! OH my poor car, at least it doesnt get rolled on its roof...yet, touch wood :D

Edited by konect
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...