Jump to content
SAU Community

Recommended Posts

I need to know everything possible to switch my car from Automatic to a Standard. Thanks in advance

trade in and buy a manual?

why go through the hassle? Your car would have to be pretty special to want to hang onto it that much i'd recon.

Link to comment
https://www.sau.com.au/forums/topic/136427-tranny-swap/#findComment-2538186
Share on other sites

trade in and buy a manual?

why go through the hassle? Your car would have to be pretty special to want to hang onto it that much i'd recon.

I live in New York (USA) and we do not have them readily available. They were only permitted in the US for a couple of years. And if I were to buy one from someone else it would cost me 70- to 80,000 dollars, If I can even find one. We drive on the left side and it is the only car in the US permitted to drive on the right side by US standards. What else would I need besides clutch pedal and manual tranny?

post-31966-1159455339.jpg

Link to comment
https://www.sau.com.au/forums/topic/136427-tranny-swap/#findComment-2538634
Share on other sites

Transmission from a RB25DET R33 in 5 speed of course

New Clutch ( I would do it since its all going to be apart)

Clutch and Brake Pedals

Driveshaft from the manual tranny

Clutch Master Cylender

Manual Tranny ECU

Those should be the main parts..

you should join up to www.GTRCanada.com were a little more local and have lots of exporters to help you find parts.

Hope that helps

Link to comment
https://www.sau.com.au/forums/topic/136427-tranny-swap/#findComment-2538699
Share on other sites

Transmission from a RB25DET R33 in 5 speed of course

New Clutch ( I would do it since its all going to be apart)

Clutch and Brake Pedals

Driveshaft from the manual tranny

Clutch Master Cylender

Manual Tranny ECU

Those should be the main parts..

you should join up to www.GTRCanada.com were a little more local and have lots of exporters to help you find parts.

Hope that helps

Thankyou much! I have linked up to "The Skyline Shop" in Canada and he has any part for them. Also I have linked up with RBmotoring in California with limited parts readily available. Do I really need to change the drive shaft despite the torque converter in an automatic tranny?

Link to comment
https://www.sau.com.au/forums/topic/136427-tranny-swap/#findComment-2538710
Share on other sites

You don't need a manual ECU! The ECU you have already will run your engine perfectly. The auto ECU is in the boot behind the seat but you don't even have to remove it since it just won't be doing any gear changes anyway.

edit - The main ECU is just in fron tof the passenger door under the kick panel, in other words there are two ECU's - one for manual and an extra one for auto.

Parts list

tail shaft or tail shaft yoke

gearstick surrounds and inner and outer boot

clutch and brake pedals

stick and gearbox

slave cylinder

master cyliner ( I think)

lines

clutch

gear stick knob

You could go for the full conversion kit second hand above for less than $3000 AUD before shipping.

There are plenty of suppliers in Australia that will supply you parts to the US. If you need help with this feel free to pm me.

While its not too hard to find most of the conversion parts it is becoming harder to find second hand gearboxes here - so for your reference its $3000 AUD for a brand new manual gearbox (just the gearbox) not including shipping.

Some extreme high quality clutches are made in Australia and you can get an ultralight 4.5kg chromolly flywheel and clutch together for a tad over $1000 AUD 12kg total weight for parcel including both.

Choice of clutch should be organic if your cars power is only lightly modified as you will have smooth clutch take up without shudder.

Edited by Edge
Link to comment
https://www.sau.com.au/forums/topic/136427-tranny-swap/#findComment-2538720
Share on other sites

You don't need a manual ECU! The ECU you have already will run your engine perfectly. The auto ECU is in the boot behind the seat but you don't even have to remove it since it just won't be doing any gear changes anyway.

edit - The main ECU is just in fron tof the passenger door under the kick panel, in other words there are two ECU's - one for manual and an extra one for auto.

Parts list

tail shaft or tail shaft yoke

gearstick surrounds and inner and outer boot

clutch and brake pedals

stick and gearbox

slave cylinder

master cyliner ( I think)

lines

clutch

gear stick knob

You could go for the full conversion kit second hand above for less than $3000 AUD before shipping.

There are plenty of suppliers in Australia that will supply you parts to the US. If you need help with this feel free to pm me.

While its not too hard to find most of the conversion parts it is becoming harder to find second hand gearboxes here - so for your reference its $3000 AUD for a brand new manual gearbox (just the gearbox) not including shipping.

Some extreme high quality clutches are made in Australia and you can get an ultralight 4.5kg chromolly flywheel and clutch together for a tad over $1000 AUD 12kg total weight for parcel including both.

Choice of clutch should be organic if your cars power is only lightly modified as you will have smooth clutch take up without shudder.

Thankyou very much :)

Link to comment
https://www.sau.com.au/forums/topic/136427-tranny-swap/#findComment-2538757
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...