Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Guest SHAYNE

Does the noise get worse when you turn your lights on? Or increase as you rev the engine? I'm assuming you're running them off an amp. It sounds like you have engine noise - usually coming from a bad earth either at the amp or deck.... let me know how it's run and I'll offer more ideas.

Link to comment
https://www.sau.com.au/forums/topic/13668-car-audio/page/3/#findComment-301382
Share on other sites

yes, the more i rev the higher the pitch goes this is noticed very easily when driving and changing gears. Yes, running them of an amp.

no, noise doesnt get worse when i turn the lights on, only when engine is started.

Link to comment
https://www.sau.com.au/forums/topic/13668-car-audio/page/3/#findComment-301389
Share on other sites

Originally posted by Nozila

Does any1 know how i can reduce the static noise coming from my tweeters? It only happens when i start on the iginition.

thanx

this was one of the problems you guys were unable to sort out for me shayne ... not that i am complaining though mate :)

i can say forsure though that there was no common earth on the deck & amps, also speaker wire's were ran very close to power wires (although unavoidable in some spots)

sorry .. rant over :(

Link to comment
https://www.sau.com.au/forums/topic/13668-car-audio/page/3/#findComment-302661
Share on other sites

Guest SHAYNE

problem with a suppressor is that its only a bandaid on the problem meaning it will only reduce the problem not eliminate it.

make sure all the components are earthed at the same point . then try running the splits of the head unit( that will tell you if the problem is coming from the amp or head unit. do the tweeters have the engine noise when the car is running but the head unit and amp are off, that will tell you if the speaker placement or crossover placement is wrong.when the system is wired as you have it now and you disconnect the rca lead from the amp does the noise go away, if yes move the rca lead.if no plug the rca lead back in and take power away from the amp does the noise dissapear, if yes try moving the power lead( this doesny always fix the problem). try powering the amp from a battery external of the car ( just sitting on the floor) that will tell you if the car is at fault . lastly is the amp screwed to the floor being metal if so try placing it on a pieace of wood thereby its only earth source is the earth lead.

Link to comment
https://www.sau.com.au/forums/topic/13668-car-audio/page/3/#findComment-305231
Share on other sites

The stupid cables have been moved all around the car!! We thought they may be running too close to each other at first and we've tried about 10 different earthing points, but I still have a slight buzzing problem...not that I really hear it anymore, I'm that used to it!!

Link to comment
https://www.sau.com.au/forums/topic/13668-car-audio/page/3/#findComment-305816
Share on other sites

mine is still annoying me, sounds like a bov from within the car when im changing gears. a very loud one at that. my earth lead is placed on the same plae as the earth for the battery, could this be the problem as both are bolted to the same place.

Link to comment
https://www.sau.com.au/forums/topic/13668-car-audio/page/3/#findComment-308718
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...