Jump to content
SAU Community

Recommended Posts

If you place a voltmeter in series along the sensor's signal wire, you should see the output voltage oscillate between 0.4V and 0.8V (for RB26). If it is outside that range, doesn't oscillate at all, or the mean is not around 0.6V, then the sensor has had it.

If you have access to a Consult cable, that is 1000 times easier, as you need to check the sensor when hot (ie. scorch your hands trying to place the meter along the wire).

Hope that helps. If you're near Western Sydney I can help out with the Consult cable. Cheers.

If you place a voltmeter in series along the sensor's signal wire, you should see the output voltage oscillate between 0.4V and 0.8V (for RB26). If it is outside that range, doesn't oscillate at all, or the mean is not around 0.6V, then the sensor has had it.

If you have access to a Consult cable, that is 1000 times easier, as you need to check the sensor when hot (ie. scorch your hands trying to place the meter along the wire).

Hope that helps. If you're near Western Sydney I can help out with the Consult cable. Cheers.

thanks for the offer mate, i'm unfortunately in WA. looks like i'll have to find or buy the cable.

If you jack up the car, follow the front pipes to where they are bolted to the dump pipes. The oxygen sensors are about two inches long and are screwed into the dump pipes. They will be the only things screwed in, look like a thick brass pen and have wires coming out the top.

It would probably be cheaper to take the car to Mr Nissan and have them run Consult to help you check the sensor function (and everything else whilst you're there) :P They'd probably charge 1h labour but you could save a lot of hassle with wiring in meters etc and it'd be cheaper than using a mechanic to hoist the car and have them do it. The Consult plug is in the drivers side fuse panel - ie. very easy to access :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...