Jump to content
SAU Community

Recommended Posts

I'm not really sure, but I reken the best way to look at it is to compare the difference between the non-turbo and turbo gearboxes across the nissan range. RB30E to RB30ET and RB25DE and RB25DET.

If you can't find any information comparing the RB20DE to the DET gearbox then try and find some information on the differences between the gearboxes listed above to try and give you some indication.

I'm not really sure, but I reken the best way to look at it is to compare the difference between the non-turbo and turbo gearboxes across the nissan range. RB30E to RB30ET and RB25DE and RB25DET.

If you can't find any information comparing the RB20DE to the DET gearbox then try and find some information on the differences between the gearboxes listed above to try and give you some indication.

thanx heaps for that mate, sumting i should think about.. aye..

But is there anyone out there that can confirm the strength between them??

thnx again

yes it does, the gears dont just break. they break because of the shock loading when you jamm it in gear ie: crunch it.

if it doesnt crunch it will last a long time. if it crunches then smash. end of story.

so the gears are the same. but the twin synchro is stronger because of the above reason.

ps. after doing 12 boxes in my dr30 i got used to knowing how and when the would pop. l series,fj,rb. the rb lasted the longest. all same gears :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...