Jump to content
SAU Community

Recommended Posts

Cant believe I could be f'ed doing this

http://www.djrperformance.com.au/dynographs.html

Very nicely inflated results there

and

oh look a Chassis dyno...not an engine brake

http://www.djrperformance.com.au/services.html

so

he was claiming rwkw's

  • 3 months later...

1989 Nissan Skyline R31 Silhouette

RB30E

GTS2 Extractors

3'' Straight Pipe

20 Degrees BTDC Ignition Timing

98 PULP

Scan_Pic0001.jpg

Also just going to mention that my car is over fueling and running extra rich so that would have taken some out of it.

  • 2 weeks later...

2007 V36 370GT VQ37HR 3.7L V6 5SPD AUTO

Modifications:

Cat-back exhaust pipes

Hi-flow panel filters

2011-09-17165602.jpg

Apparently car runs rich from factory, bit more power to squeeze out of it if I can lean of the a/f ratio a bit

Stock Power run done close to when I first got the car for reference:

2011-09-17165537.jpg

th_video-2011-09-17-11-49-21.jpg

  • 3 weeks later...
  • 1 month later...

+1

also love how the radiator hoses are put as a modification

I thought this thred was for dyno figures? apparently not.... Anyway, Ive only put down what was read out at the car show where the dyno run was done, And I thought the turbo r34 standard are 208kw and the gtr 280kw? From what I've read about a million times N/A RB25de neos do about 147kw standard?? is this wrong coz the thing will keep up with my mates boosted s14 no problem?

I thought this thred was for dyno figures? apparently not.... Anyway, Ive only put down what was read out at the car show where the dyno run was done, And I thought the turbo r34 standard are 208kw and the gtr 280kw? From what I've read about a million times N/A RB25de neos do about 147kw standard?? is this wrong coz the thing will keep up with my mates boosted s14 no problem?

both the r34 GT-t and the GTR are quoted as having 206kw at the flywheel (all factory quoted figures are at the flywheel) however the GTR actually puts out more power. and yes, the non turbo is 147kw (again, at the flywheel) which would work out to be about 150hp at the wheels

  • 2 months later...
  • 3 months later...
  • 4 weeks later...

R31 Skyline Series III Ti

RB30E

Stock Motor Done Near 800,000K's - Runs A Little Off Beat

Runs a rusty old set of extractors with old stock exhaustand had 4.11 Diff ratio which was stuffed open wheeler "Just about to install 3.23 LSD"

New GTS1 Cam, Timing Kit, Plugs & Leads - Installed 6 Weeks Ago!

15" Ti Alloy mags

Does 10KPL Religiously & equates to almost 600K's Per tank

Am shortly contemplating in dumping the NA high comp motor that I've got with around 80,000K's on it and VLT auto trans that's only done a few hundred K's along with Hi-tech headers "Stainless" and 2-1/2" sports exhaust. WIll be interested in seeing if the figures change much along with the 3.23:1 LSD installed.

  • 2 weeks later...

Just got my v35 350gt8 a week ago. runs 200kw at flywheel stock. Waiting on a few parts to turn up.

Used to have a na b18c type r powered crx with a few bits here and there running high 12s low 13s.

bout 180fwkw

Gonna try and beat that with the extra na displacement.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...