Jump to content
SAU Community

Recommended Posts

Hey peoples!

Our timing belt went on the weekend! We have the new belt, were not sure if it has done any further damage? hopefully not ! Does anyone have any idea how to put it back on and in the right spots after its snapped? We have asked a few machanics in town and no one wants anything to do with our car??

Any ideas would be greatly appreciated! its only just got back on the road after the yellow sticker and now this??!!! ahhh

anyway, anything would help.... its a R33 95 GTST

cheers !

Link to comment
https://www.sau.com.au/forums/topic/138247-timing-belt-replacement/
Share on other sites

go to a workshop. hyperdrive should be happy to help

if u f**ked it up bye bye engine

they are in geraldton :P

theres a guy at tyrepower in geraldton that owns a white 33, maybe ask him where he gets his car serviced?

Don't screw with it because it is a very important part of the engine! I got mine done at a workshop which will remain un-named, one different to where my performance mods are done, and for that reason I believe they didn't take the care they should have with it. Timing was way out when I got it back, and it made it hell.

Take it to somewhere that has dealt with your car/previous cars before & you can trust. If that doesn't apply, somewhere convenient for you.

DIY I say - I did mine, with a bit of common sense and a willingness to learn its pretty simple :P

Absolutely!!

I have done numerous RB timing belts and a few others. The Gates belts have lines on the. If you point the dowels on the cams up and set the bottom end to TDC then line up the belt marks with the punch marks.

Of course its VERY important not to turn the bottom end independent of the cams, otherwise the valves will hit the piston tops and bend, if that hasnt already happened. The way around this, remove the cams so the valves arent depressed, easy.

Brent.

Of course its VERY important not to turn the bottom end independent of the cams, otherwise the valves will hit the piston tops and bend, if that hasnt already happened. The way around this, remove the cams so the valves arent depressed, easy.

Brent.

I lined up my cams to the marks on the timing cover, THEN turned the bottom end over 39849384 times to make it all line up with TDC, worked fine for me. I can only assume by this logic that keeping the cams on thier marks, keeps them totally clear of the pistons??

P.S. Yes, my engine is fine :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...