Jump to content
SAU Community

Recommended Posts

I was looking at some oil and purchased Mobil 1 as I was getting problems with a slight tick first thing in the morning and when she was warm she would also tick on and off every now and again.

Anway Oil change did the trick no more tick BTW the turbo is on her way out and does blow a little more smoke when cold for the first two gear changes (second and third) then it goes away and never comes back until cold again, I've been told it is the oil seals seeping when the turbo starts to cool down?!?!

ANYWAY FOR THE OIL FILTER!!!

I went to Autobarn in Adelaide and the bloke there told me to buy the Purolator PureOne Oil Filter, Apparently it is a better oil filter than the Ryco or similiar.

I slapped in the oil and I get consitant oil pressure all the time now ?!?!?!?!? The guage used to fluctuate up and down and some times when on idle it would sit on around 1/8 which looks way to low.

Oil pressure now never sits that low and the tick is gone?!?!?!

I am wondering if the Ryco oil filters are what causes the fluctuation in oil pressure, I have run Mobil 1 before with a Ryco oil filter and had the same pressure fluctuation.

It could be just coincidential but it sure doesn't look like it.

Here's my Oil pressure now.

Idle - on the first line or on the 6 when cold.

Normal driving on the 4.

When driving hard havn't really noticed.

WWW Site.. Click on the PureOne title towards the top left of the screen. The Premium Plus oil filter is their std. oil filter.

www.pureoil.com

Try the Oil filter and let me know.....

I've always used ryco and never have any complaints. Once I tried a genuine holden VL filter and found it was a bit more restrictive. Note that I kept using the same oil (mobil 1).

Sounds like your guage was playing games and could just fortune.

according to the manual oil pressure should be at 4kg cm2 @ 6000rpm

mine sits at about 1/2 or sometimes lower on a cold night at idle and i get pretty scared seeing it so low.... although it rises fairly quickly when you put the hammer down. im going to change oil and filter soon and have been advised toward a ryco or preferably genuine nissan and i use AGIB oil. could the change in the oil/filter combination change actual oil pressure that much? or are we relying too much on the std gauge.... cos i know low oil pressure=bad as can mean internal damage or dead oil pump which mean rebuild

  • 1 year later...

Ok, I had problems with pressure and Mobil 1, i wont touch the stuff now. Always used ryco filters, no problems at all. Im using Conoco synthetic oil atm and it great. Also my factory oil pressure gauge consistently reads lower than what my aftermarket one does too, especially at idle and high rpms.

-rb25

Hehe,

I always have used Ryco oil filter z145A, and also now use Castrol Synthetic R 5-30W.

Obvioulsy the stock gauge isnt very accurate in terms of fluctuation and instant readings, however at idle, when warm it reads 4. When i accelerate at WOT it usually gets to aprox. 6. Is this the same with everyone else?

mine, no matter what oil is in it, sits on about 2.5 at anything over 1250rpm. never goes higher than that.

have used 5-50, 10-50 & 5-40

at idle is usually about 1.5 but occasionally drops right down

will have to check it with an external gauge in case it is actually the pump!

Guest RedLineGTR

This is a good rear if you have abit of time, pretty much on the topic about different filters and oil pressure. http://theoildrop.server101.com/ubb/ultima...ic;f=6;t=000513

Its from this site: (not aussie related)

http://www.bobistheoilguy.com/

Very good info and some nice test. Cheers Rob

mine, no matter what oil is in it, sits on about 2.5 at anything over 1250rpm. never goes higher than that.

have used 5-50, 10-50 & 5-40

at idle is usually about 1.5 but occasionally drops right down

will have to check it with an external gauge in case it is actually the pump!

i have the same problem as you... but like today i was driving down the road and i watched it go form just under the 2 mark upto about 3 than about 5 mins later frop back down again... when i start it in the morning it does just under the 4 than drops to just under the 2, than after about 15mins of driving it does down again.. than if i pull over and stop somewhere for about 1 min or 2 than start up it will be right for another 15 or 20 mins or so...

its got me stumped.... dodgy gauge i think

i have the same problem as you... but like today i was driving down the road and i watched it go form just under the 2 mark upto about 3 than about 5 mins later frop back down again... when i start it in the morning it does just under the 4 than drops to just under the 2, than after about 15mins of driving it does down again.. than if i pull over and stop somewhere for about 1 min or 2 than start up it will be right for another 15 or 20 mins or so...

its got me stumped.... dodgy gauge i think

There's a thread some where about this issue.

Its two things it may be..

1. Dodgy oil pressure sender/guage

2. The bolts are coming loose in the oil pump causing it to loose pressure.

Strangely enough I had to stop using Mobil 1 5-50 I think it was as after giving it a hard run or driving in peak hour traffic for a long period of time my oil guage would show just above the 0 line.

I tried several different oils with similiar results.

I then came across a cheapish Penrite HPR10 which has a vis of 10w-50. That never plays up for some reason. Even after its had a hard time. It does start to loose a little bit of pressure if I start going over 7000km's without an oil change though.

Mines done 160,000km's.

I also found with the Mobil 1 and any 15w-x oil I get a ticking every single morning from the hydraulic followers I assume.

Not sure why but my car doesn't like Mobil 1.

right... my car has done 169,000km's and i have used about 3 or 4 different oils from 10w-40 to 25w-50... maybe the penrite oil has some sort of cleaning agent in it and unblocked something?? who knows

with the bolts on the oil pump, how hard is it to tighten them up again??

Mine stays at 4 when i first start it up. After it warms up though it drops to that first line under the 4. Also starts ticking at this point.... But then on accelerating it rises again to 4.

Is anything wrong?

I'm going to get the car serviced on saturday, so hopefully all this will be fixed.

wil..

  • 4 weeks later...
right... my car has done 169,000km's and i have used about 3 or 4 different oils from 10w-40 to 25w-50... maybe the penrite oil has some sort of cleaning agent in it and unblocked something?? who knows

with the bolts on the oil pump, how hard is it to tighten them up again??

When I rebuilt my engine recently I found that the counter-sunk screws ( not bolts ) on the inner surface of the pump were very lose. If these are the ones you're talking about it's a matter of pulling the oil pump off which is NOT an easy job !

In my opinion.......never trust the stock oil pressure gauges / senders in an import skyline ( especially the R32 ones ). I have a freshly rebuilt engine and it reads fine on start and while cold running. When it gets hot it still reads fine until idle at the lights and then it drops off to zero.

For the record I've been using Penzoil 5W-50 which seems OK but I get cold engine ticking most of the time no matter what oil I use. Also, I'm another who will not use Mobil 1.

Up until the last oil change i had always used Mobil 1. Speaking to a guy down here, im now trying an oil called OWS or something.

One thing i noticed when i had the rocker cover off my engine on the weekend, for an engine with 170,000kms on it, the valvegear looks to be in good nic, far better then i expected.

So of the 170,000 kms, 95,000kms by me using Mobil 1 and the engine has negligible blow by, even compression accross all cyliders etc etc... so the oil cant be that bad... i suppose as long as you change it regularly you cant go too far wrong

my r32 has a few k's on it, when i used to use fully synthetic oils my oil pressure would sit lower than 3 on the stock gauge........i've now changed to Penrite HPR 40 (the old pentrite turbo stuff) which is i think 30W-70 and i've never looked back. Oil pressure is now on or above 4 while driving.

Only one thing, it need a good warm up in winter.

My 2c

  • 5 months later...

We just had a hot day the other day 36 degrees at 4 pm and while drivin home i found that my oil pressure sat just off the 0 :D which is really freakin me out. So i changed the oil in the car. Put mobil 1 in it and and changed to a nissan ginuine filter now at idle it sits on the mark above the 0 so i gather 2. Its still concernin me. Any ideas. Not sure what oil was in it as i haven't changed the oil since i bought it. from a dealer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...