Jump to content
SAU Community

Recommended Posts

post-32230-1160823598.jpgG'day guys, i recently bought an r34 gtt and would like to put the boost up. the only mods i have are exhaust, intercooler, and now a boost controller. as far as i know its ok to have 14psi on stock? do you think thats ok or will i fry things like the turbo? what is a good boost to run on the neo 6??
Link to comment
https://www.sau.com.au/forums/topic/138693-upping-the-boost-on-r34-gtt/
Share on other sites

most people say 10-12psi. it really depends on when the ecu hits rich and retard. you will know when you hit this as it kills the motors power. it retards the timing and richens the fuel right up.

i run 14psi on my 33 with a remapped ecu. goes a lot better than 12psi, and when my turbo blows i have an excuse to get a new one.

so i could run the standard boost on low and maybe 11psi on high you think and that should keep me happy and stop me from spending more money. after buying the car i dont have much of that left! she's only done 35000 k's!

I found 34 gtt's hit r&r a lot easier and harder than r33's. I dynod one stock, and then after a turbo back and front mount, nothing else, and r&r was savage, lost up to 30 kw, only gained about 5kw after it clawed its way out of the hole.

well maybe you coulod get a fuel cut defender, or if in your budget just get a pfc now save your hassles later on, just a thought if not try 9-10psi if it retards then just back the boost down, it will still feel better than standard.

Have a look in the trader section search a user by the name of performance-wise he does group buys on powerfc's with the handcontroll for under 1000 delivered i just bought a unit through him very good to deal with.

They are a complete engine management computer which replaces the standard ecu allowing the car to be very efficiently tuned getting the most out of the engine and its modifications.

Edited by fEkuaR
Have a look in the trader section search a user by the name of performance-wise he does group buys on powerfc's with the handcontroll for under 1000 delivered i just bought a unit through him very good to deal with.

They are a complete engine management computer which replaces the standard ecu allowing the car to be very efficiently tuned getting the most out of the engine and its modifications.

thanx man, just checked it out, should i still be buying my electronic boost control or does the power fc cover that as well?

thanx man, just checked it out, should i still be buying my electronic boost control or does the power fc cover that as well?

You can use a apexi boost control kit that goes with the powerfc. Or you can just run a seperate boost controll unit. The boost controll kit with the powerfc is a little extra but if you havnt bought a controller yet id go with that and get it at the same time you can buy it with the group buy aswell.

most people say 10-12psi. it really depends on when the ecu hits rich and retard. you will know when you hit this as it kills the motors power. it retards the timing and richens the fuel right up.

i run 14psi on my 33 with a remapped ecu. goes a lot better than 12psi, and when my turbo blows i have an excuse to get a new one.

When your turbo blows the smaller ceramic particles that can result can find thier way back into the engine. This is why blowing the stock turbo isn't a good 'plan' even if it's the excuse you want to buy a new bigger one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...