Jump to content
SAU Community

Using A Q45 Afm?

ix9

By ix9,
in Engines & Forced Induction

 Share

Recommended Posts

ix9 Grand Master

ix9

Posted
Posted

Hey Guys,

My AFM appears to be screwed, it will randomly drop to 0% while driving, or putting my foot down will make a sucking noise but do NOTHING until I release and re-apply a few times!

Checked the plugs etc.

The S-AFC-II says its going to 0% if I keep my eye on it, at random times :P

Is it possible to use a Q45 AFM to replace the stocker? ie with the use of my S-AFCII ?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/
Share on other sites
The Mafia Grand Master

The Mafia

Posted
Posted (edited)

nope, the q45 is HEAPS bigger than stock, so you'll need some form of adapter.

Get a z32, its a direct replacement.

How do I know? I'm using a q45 :laugh: But on a Garrett GT30..

Edited by The Mafia
Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/#findComment-2590498
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

im using one too.. GT3582R - you can get the apexi power flow pods which have the bolt pattern for the A45. see KUDOS motorsports - he is sponsor on here. great guy awesome service. I just got a setup from him because.. ummmm.. lets just say i ran over my Q45 AFM and POD. Long story =)

Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/#findComment-2590516
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

Super cold air induction.. :laugh: AFM and filter was sitting in the air scoop of front bar. it bottomed out and got run over... Dont laugh.. someone on here had it happen to them and I laughed at them :huh: bad karma

Link to comment
https://www.sau.com.au/forums/topic/139080-using-a-q45-afm/#findComment-2590661
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Intro/R33 owner

      By PranK · Posted

      Welcome!  How long have you had it? And what colour is it?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      "CAD" version 1.0 It will have a 15mm lip around the top for 6 × 5 or 6mm nutserts and fixtures (two on each of the three straight edges), and some pinch weld on any exposed edges, it has three mounting points, one of the power steering reservoir bolts, and two on the rad support, my 120mm hole saw will make short work of hole for the silicone joiner, with ample room for some pinch weld  I've also got enough Carbuilders "peel and stick" heat shield to cover the outside of it at the coolant expansion tank and on the engine side, as pictured, and internally on the lid and where the fuse box is, I've also got some thin, about 3mm, black 3M single sided sticky foam stuff that was left over after sealing some door drafts at home to help seal the lid As for the shape, it "sort of" matches the shape of the fuse box, so shouldn't look to "out of place" The lower area and hole for the intake will need pinch weld with a balloon on it to fully seal the hole and bottom of it, that will happen after it has been fabricated so I know exactly what size is required  Filter service has been trialed,  and so far it was a simple process  Just need to get some alloy, and then head into work to use the guillotine and break press in the workshop Hopefully it should be sorted in a week or two Guestimated outlay will be under a $50 for the stuff I don't have on hand (alloy, 6mm nutserts, the pinch weld, and wrinkle paint) Disclaimer: That's what the "voices in my head" are telling me how the filter box should end up getting done......lets see if they know what they are talking about  
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Have been polishing up the trailer rims as they had been sitting in the shed for a few years and are really in need of some love. This was after a couple of passes with chrome polish - coming up quite well ✅ .
    • MBS206
      Intro/R33 owner

      By MBS206 · Posted

      Welcome aboard! Is your Skyline auto or manual? I'm assuming manual. Does it have any mods done yet?
    • Yeetus
      Another "where do these lines and plugs go" RB25DET question

      By Yeetus · Posted

      Hey mate, the brown and grey plugs would usually go to the TPS, brown one goes on the bottom connector and grey is the top but isn't used unless the car is auto, your TPS looks different to mine though I've got a series 2 engine.
×
×
  • Create New...