Jump to content
SAU Community

Recommended Posts

Grab a GCG Highflow for that sort of power.

I think SydneyKids group buy for $1750 or there abouts is still running.

The GCG Highflows bolt straight up with no more to spend.

Buy something that doesn't bolt up and your up for another $200-$300 worth in sorting out silicon hoses and water/oil lines not to mention another $300 odd for a custom dump pipe.

oh yeh not bad... wat other turbos would you reccomend for 250-260kw?

GARRET 3040 DIRECT BOLT ON THE STANARD MANIFOLD GOOD FOR ABOUT 250 TO 260 RWKW I HAD ONE ON MY RB25 IT MADE 255RWKW ON 18 PSI

Edited by blitzxtr
GARRET 3040 DIRECT BOLT ON THE STANARD MANIFOLD GOOD FOR ABOUT 250 TO 260 RWKW I HAD ONE ON MY RB25 IT MADE 255RWKW ON 18 PSI

Why would you want all that compressor flow when the hot side is unable to support it. Your trading nothing for............... lag. :laugh:

Why would you want all that compressor flow when the hot side is unable to support it. Your trading nothing for............... lag. :laugh:

What do you mean by unable to support it & lag there was not much lag full boost by 3500 GO BACK TO YOUR DESK PROFESSOR & STAY OUT OF THE GARAGE

Edited by blitzxtr

lmao mr make full boost by 3500rpm keyboard warrior. :D

So your telling me the GT3040 .63 hot side will make complete use of the compressors air flow ability. hrmm why is it Garrett didnt release such a combination......

Its not just lag its also response that will be affected by running a large compressor.

For the power this blokes after a GT3071r will be perfectly fine, offer better response than the GT3040 and still make the power he's after.

I've seen a GT2871r make 240rwkw with stock like spool on an rb25. I'll try to dig up the dyno sheet from the dyno day.

My opinion only (shared by most of the production engineers at Garrett in Torrence California) .

The GT3040R has too large in diametre a compressor for the GT30 turbine , it struggles to produce enough turbine shaft power to drive a high capacity compressor ie with that much sail area . This is why HKS only offered their spec GT3040R in the smallest available 82mm GT40 compressor trim - 50T , the Garrett marketed one at 56T is far laggier by comparison .

DO yourself a favour and stay away from the GT2876R , its the same deal only scaled down overall . I will confirm but from memory it uses the hopless TO4S compressor and only T28 flanged exhaust housing are available from Garrett . If it uses the cropped GT30 turbine I suspect it does turbine efficiency will be woeful . Same old story , long shot by Garrett to get more gas flow through the T28 turbine housing family and the concept failed to deliver . Only HKS exhaust housings work with the "cropped" turbine because they are GT30 turbine based castings dimensionally and have the right nozzle design .

Back in five .

Danger Will Robinson - avoid this lump . The dog turbo uses a 48 trim T04S compressor in large bulky heavy TO4S comp cover .

The turbine is not the cropped GT30 turbine but the normal high performance GT28 turbine .

I reckon T28 flanged anything is pointless for Skylines that use the T3 mounting flange on their exhaust manifolds . The real GT3071R , and no not the GT3071R WG version , should work well . Garrett now sells T3 flanged integral wastegate exhaust housings so they will physically bolt to the std exhaust manifold - provided the compressor cover clears it .

People have found the GT3076R and HKS GT3037 56T (same centre section and wheels) a little laggy on street cars , HKS also does a 52 comp trim version but they're thin on the ground in Aus .

The real GT3071R (insist on cartridge or CHRA no 700177-0023) is probably the best compromise unless you can afford exotics such as HKS brands .

You can find its details and pics at ATP Turbos web site .

Cheers A .

So would that turbo(gt3071r) be the next step up from the GCG hi-flow?

And having bought it, how much extra would it cost to assemble all the parts to bolt it up on the weekend?Surely someone must make a complete package or at least a one stop shop where I could buy everything for a reasonable price.

People do tend to push a bee's dick more out of them than the GCG highflows.... But they do cost a little more to get on the car.

No packages are available that I know of... Simply buy the turbo; suitable water/oil lines bolt it on and then take it to an exh. shop to have a dump pipe made up. Or.. Machine up your Skyline turbine housing to suit; by this time the machining costs even out with the costs of a new dump pipe. I know what I'd rather; a new dump pipe with the correct unmolested turbine housing.

What about sticking with my hi-flow and adding a vg30 exhaust housing? Though I must admit the ability of the wastegate to control boost would worry me.Perhaps a slightly bigger ,say 1mm wastegate would help.Enough to flow 240kws at 17lbs.

What do you mean by unable to support it & lag there was not much lag full boost by 3500 GO BACK TO YOUR DESK PROFESSOR & STAY OUT OF THE GARAGE

What gear?

Street or dyno loaded?

There is a key difference there, its also on/off throttle response that is just as crucial as peak power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...