Jump to content
SAU Community

Recommended Posts

Okay, this is seriously a newbie question, but I have just put my new stock R33 GTS-T through a dyno to measure the initial power before any mods were done to it.

Why is the max power only at 132kw instead of the 180kw which it was supposedly able to do in the official R33 specifications?

No wonder it felt kinda slow. Kinda dissapointed and can't wait to fit some mods. :laugh:

p1010633largedx7.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/139745-power-output-in-stock-r33-gts-t/
Share on other sites

all figures in magzines, flyers, brochers, dealers etc are all flywheel

ie: at the engine / clutch system and not at the rear wheels.

a stock gtst in 4th will make around 130 to 140rwkw.

all the hsv's that have the 250kw badging and "figures" are all the flywheel

so they would make around 200rwkw. a 200rkw skyline would smoke it no worries

The R33's come with a dual stage boost control solenoid that switches from low to high boost mode at roughly 4500rpm (about the same time the variable inlet cam kicks to advanced setting). It's mounted in front of the passenger side strut tower with 1 hose going off to the intake before the turbo, then another with a t-piece splitting off to go to the wastegate actuator & the intake after the turbo.

Why nissan set them up with the dual stage control like this I have no idea, makes the car a lot peakier to drive though. When you get another boost controller you can set it up for the same boost at lower revs. Far more Torquey

Edited by JazzaR33

Mate, my R33 was on the dyno at Mercury a bit over a week ago and it made 149.4rwkw, again on a completely stock car. If you compare the graphs you'll see that i'm making around 20kws more through most of the rev range, but more importantly you'll see the difference in boost. I've grounded the wire going to the boost controller so it's in high boost all the time, but yours should still get there in the end. I'd be looking at your boost controller first, maybe read the thread on staying constantly in high boost mode and give that a shot.

dyno.jpg

My RB20 made 196.4kw with some small mods. I think the R34 Turbo made a big difference. Dyno Results are on my Signature. Shoebox I suggest you get rid of the Dual Stage boost and just run a constant 8-10psi. >_<

:P

Edited by r32matt

well I had 145rwkw completely stock and when i got an exhaust it went to 170rwkw. how do i do the adjustment to get hi boost from stock controller all the time??? havent heard of that yet. Thanks!!

and it should be at 5psi before that. i'd say you have a split hose of something causeing a boost leak.

okay, i'll ask him about it tomorrow. split hose!?! don't scare me! =_=

but i really doubt that it's a mechanical fault, as i sent this car down for a pre-purchase inspection a few weeks ago, and it cleared except for an oil leak from the tappet covers, castor bushes which are about to split and spark plugs which are one heat range lower than they're supposed to be.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...