Jump to content
SAU Community

Recommended Posts

I run an ARC twin entry intercooler kit on my GTR(same as the mines one) The kit comes with plugs tp block off the BOV's. The car runs 370-380rwkw and 22psi. The combination of this cooler and blanking my BOV's resulted in 25kw extra mid-range. I don't know how much is associated to the cooler or lack of BOV's, however the bleed hole that recirculates air(whilst the BOV is closed) can only delay spoolup.

Midrange wont be from the BOV's, its impossible to allude to the fact this is so.

How can something that only operates on throttle off... possibly increase power unless its faulty to begin with? because it simply cant :ninja:

I bet if you put the stock BOV's on, you wouldnt notice a difference in the power

Personally Im going to run a turbosmart plumbback 38mm. (Refer my signature)

2 reasons;

1. Emissions (Im still running an AFM so i want the air to recirculate, keep the mixtures lean and rule out over fueling to prevent stall)

2. Legality (The popo wont book me for chatter in other words loud noise's)

for anyone wanting to compare a race car with no bov to a road car, consider the following-

using qld raceway as an example, a race car will lift of from wide open throttle 6 times (there's 6 corners isn't there).

now if you take your car to the track, on a flying lap, from the start of the straight to the start of turn 2 you will have lifted off the throttle more times than that. race cars don't lift off on gear changes. most don't even use the clutch.

so why would a race car need a bov? the slowly wind the accelerator on just after they turn the car into the corner, so if there is any extra lag from not having a bov, it doesn't worry them as they don't really have any on/off throttle aplications.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...