Jump to content
SAU Community

Recommended Posts

So i was driving today along beecroft road, when all of a sudden i pushed the clutch pedal in and it felt like it snapped on me. Now changing gears is difficult, and the friction point has gone closer in towards the firewall (i.e. i bring the pedal out like half a centimetre and it feels like the cars gonna stall). The pedal's all kinda wobbly now too and much looser than it used to be.

Any ideas?

Btw its an r32 GTST with an aftermarket heavy duty clutch (not sure what type - came with the car when i bought it)

Link to comment
https://www.sau.com.au/forums/topic/141697-clutch-problem-diagnosis/
Share on other sites

Could be your clutch fork. I know of a person who snapped their clutch fork because he had brassy put in his car but the fork wasnt changed... im not sure if you can change the fork to one which can handle a heavy duty clutch but it could be the problem.

Edited by gtrchick

haha yeah...im bored

So your clutch fork is what is acted upon when you put your foot on the clutch, which displaces the liquid via the clutch master cylinder, to the slave cylinder, which pushes on the fork, on the fork is your throw out bearing which is what makes contact with the pressure plate fingers.

The clutch fork is what helps changes the clutch from being engaged to disengaged.....sort of. You get the drift

hmmm then again if the pedal is wobbly.... did you check the pedal? like the pivot and all that jazz? could be something really simple...

Edited by gtrchick

I was thinking pedal box as well. My one died but it didnt snap so to speak, it slowly mangled and twisted itself into a mess.

The pedal box doesnt cost much, but it isnt a fun thing to change. Think drivers seat fully reclined, and laying upside down with head under the dash and blood rushing to your skull why you have no room and cant see sh!t!! LOL.

Its a common prob with heavy clutches, so if it is infact your problem just reinforce the new or old pedal box so it dont happen again. They are only made from thin folded tin with a scarce spot weld here and there.

If it is the peddle box, get you head under the dash with a torch and look up at the peddle box while you press the clutch to the floor. If it is cracked you will see it flexing open at the crack while the clutch is being operated.

Two bolts hold the master cylinder to the firewall, they also hold the peddle box, undo the nuts from the master cylinder, take the clevis pin off clutch lever, there is one bolt that goes up to a support behind the dash, long extension on your socket can get that, it should then just come out.

Once out just get it welded and reinforced.

If the pedal box is broken, the clutch pedal itself should be sitting closer to the floor when in "clutch out" mode.

I've actually had mine break against the standard clutch. Had a HD clutch for a while now, and it's still OK.

Removing the pedal box, there is a bolt up the top, which I found much easier to remove after I removed the instrument cluster.

apparently the little casting in the shape of a ball inside the bell housing of the gearbox, that the clutch fork pivots on can break aswell.

i have had the clutch pedal bracket/box snap into pieces on me.. couldnt use the clutch at all. took it out and welded it back up. If it happens again, i will tig weld the seams top to bottom. but its been a year with an xtra heavy duty button xtreme clutch and its all good.

also got to watch the ram that is attached to the clutch master cylinder isnt bent or is leaking. mine has started to leak over the last week.

Wish i knew where to get one

apparently the little casting in the shape of a ball inside the bell housing of the gearbox, that the clutch fork pivots on can break aswell.

i have had the clutch pedal bracket/box snap into pieces on me.. couldnt use the clutch at all. took it out and welded it back up. If it happens again, i will tig weld the seams top to bottom. but its been a year with an xtra heavy duty button xtreme clutch and its all good.

also got to watch the ram that is attached to the clutch master cylinder isnt bent or is leaking. mine has started to leak over the last week.

Wish i knew where to get one

Not 100% sure on what u mean by ram attatched to master cylinder but assume you meen the actuation rod for the m/cyl which is attatched to the clutch pedal. if that is the case you need to replace the master cylinder the leak you refer to is actually brake fluid leaking out of the rear seal of the master cylinder, that can be sourced from most brake shops eg Better Brakes etc.

i'd say the pivot bolt. that is what the clutch fork pivots on. there are 2 places it could've broken. either at the base of the bolt, (this is usually caused by it being done up too tight) or at the head. i know of 3 r33's (mine being 1) that have done this. mine and another broke off at the base, and another snapped the head off.

you can buy a new one from www.uniqueautosports.com for about $55. i got mine repaired by an engineer mate of mine. i got a 50mm long bolt in 12.7 tensile (thats pretty strong), got my mate to machine the old pivot polt smooth at the base, drill a new hole, tap a thread in it and cut the head off the new bolt and screw it into the pivot bolt. cost me 90 cents.

it is a gearbox out job. if it has broken the thread off it isn't that hard to get out. i used a cutting disc on a dremil to score a little groove in the top and just screwed it out with a screw driver.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...