Jump to content
SAU Community

Dominator Car Alarm Troubles

aphid

By aphid,
in Car Audio & Electrical

 Share

Recommended Posts

aphid Proficient

aphid

Posted
Posted

Hey there,

hoping somebody can help me with my prediciment.. i have a dominator car alarm i bought to replace my dodgy old VDO one which crapped itself and after seeing the absolute dodgy job which had been done when i chose to have it 'profesionally' installed last time i decided to install it myself.

everything on the ignition side of things was connected as per the wiring diagram and then checked at the plug that connects into the alarm unit itself with a multimeter for correct voltages at all stages of the key turn (off, acc, on and start as well as the +12v and the chassis earth connection). the relay was also installed as per the wiring diagram

at this stage i decided to attempt to start the car and found the car would turn over just fine, which of course it shouldn't have with the unit it place.. at first i thought i must've made an error in wiring in the relay, but i went over it and found that it was all good and as per the install diagram. the harness the relay plugs into is all colour coded which makes me believe the manual is wrong.. the alarm actually features a remote start button so i think this may have something to do with it, but really unsure.

i then tried to use the remote, but the only signs that the alarm was even alive were a few faint relay clicking sounds coming from inside the unit when i turned the ignition through it's variouse stages.

i then wired in the siren, thinking that perhaps as this was listed as the backup battery it was required to make the alarm function.. there was no clear diagram on how to wire this in, only a trigger wire was specified on the main harness, however there was a pinout on the back of the siren itself so i improvised and ran the +12 and -ve earth connections (multi meter tested) and ran the -ve trigger to earth and ran the positive trigger wire (as specified on the back of the siren) to the alarm wiring harness.. and still no change

at this stage i read a sketchy bit on how to program in the remotes in the install guide, and followed it as best i could (ignition on and off 4 times, then press all 4 buttons on each remote you want programmed in.. from memory), and still nothing..

i also connected the variouse shock sensors etc up to see if that would make a difference and none of the lights on the sensor units would come when i shook them.. the status light also had the wrong connector on it and would not plug into the main unit, so i improvised and found a connector to suit and wired that in and found that the status light wasn't coming on either..

i'm starting to believe that i have a dodgy alarm unit but perhaps i've screwed it myself doing the install.. but if anybody else has any idea's or has had simerlar experiences with the alarm in question then please help me out :pirate:

thanks in advance guys,

mark.

Link to comment
https://www.sau.com.au/forums/topic/141799-dominator-car-alarm-troubles/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      RH9 R32 GTR Build Thread

      By soviet_merlin · Posted

      Out of curiosity, how do you cover up the inspection hole? Surely it doesn't sit open like that, right? With grime and dirt coming in and oil going out?
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Hi from Canada, Both of my calipers are starting to fail. My car is a 2005 M35 Stagea ARX and I can't seem to find any parts or any cross reference caliper that would fit my car. Is there a company or a similar caliper that would fit and I could replace the OEM one. Or if anyone knows where I can find a new OEM. Any help is very appreciated. Let me know!
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • Matt Z
      SAU NSW - Bathurst Run 2025

      By Matt Z · Posted

      🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...