Jump to content
SAU Community

Recommended Posts

hey guys,

getting on the on ramp today, i heard a little pop sounded like air escaped, and felt the car go off boost, and thats the end of that.

the exhaust on the car now runs at least 5 times louder.

im not a guru, with anything mechanical with cars, im assuming im dealing with a dead turbo?

and is it safe to drive teh car around? or am i better off not driving it until someone checks it out?

cheers mark.

Link to comment
https://www.sau.com.au/forums/topic/14285-dead-turbo/
Share on other sites

Is there any smoke coming from the exhaust? If so it's probrably turbo. Does it sound like the turbo is very noisy? OIs it no longer boosting at all? If so it sounds like the turbo, or, it could simply be a leak - could be intercooler piping.....

Link to comment
https://www.sau.com.au/forums/topic/14285-dead-turbo/#findComment-288211
Share on other sites

I'd put money on it that your turbochargers exhaust wheel is now somewhere within your exhaust system (lodged in the cat) or possibly gone completely if you don't run a cat?

The much louder exhaust note would be due to the fact there's nothing much left in the path of exhaust gases to quieten it down.

It would take a monumental exhaust manifold leak to lose ALL boost, so you can count that one out. Not to mention the noise from the leak wouldn't sound like any exhaust I've ever heard. I've heard a nasty RB25DET exhaust manifold leak - horrible chuffing/screeching noise :P

If the shaft/bearing assy is still intact (no reason for it not to be) then you won't see any smoke out the exhaust.

As Secoh mentioned, get it checked asap! If the compressor wheel is unbalanced & has send fragments through the rest of the IC piping (tends to happen if the turbine isn't there anymore) then it won't be good for your IC, & even worse, engine internals!

Link to comment
https://www.sau.com.au/forums/topic/14285-dead-turbo/#findComment-289270
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...