Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Working on a 2.9L (88mm bore x 79mm stroke), but it will not be available

until Jan-Feb 2007.

Pricing depends on the style of rods, but in the neighborhood of $5000 w/BC Pro

Series (1500HP rating) or $5800 if Carrillo rods desired.

BC 4340 billet steel crankshaft.

BC 4340 Econo or Pro Series steel billet rods w/ARP 220,000 psi fasteners.

CP aluminum forged pistons (any bore size, any compression ratio).

9310 nickel carbon steel alloy wrist pins.

Ductile iron plasma top rings, tapered second ring, low tension oil rings.

Fully system balanced and ready to install.

88x79 gives you 2.883 L so i think it would be much safer to go 87x79 for a 2.818L

2.9 is pushing it.

Hmmm...I can wait. 88 seems big though.

Edited by Scooby

Only about 9500rpm

Tomei 2.8L Stroker, Valve Springs, Cams..etc

Nismo Oil Pump

N1 Water Pump

N1 Block

Extensive Port & Polished head

HKS T51R SPL BB

HKS 62mm Gate

4inch Throttle Body

Motec M800

Motec CDI

Custom Plenum

Water To Air Intercooler

2 Bosch 044 Pumps

1000cc Injectors Sard

Custom Sump

Getting sore fingers now..

Alot of other stuff.

Only about 9500rpm

Tomei 2.8L Stroker, Valve Springs, Cams..etc

Nismo Oil Pump

N1 Water Pump

N1 Block

Extensive Port & Polished head

HKS T51R SPL BB

HKS 62mm Gate

4inch Throttle Body

Motec M800

Motec CDI

Custom Plenum

Water To Air Intercooler

2 Bosch 044 Pumps

1000cc Injectors Sard

Custom Sump

Getting sore fingers now..

Alot of other stuff.

So Rhys (sorry can't remember spelling) you finally have it running...that's great!!

Edited by Mik

dude i dindt know that they put power FC's into F1 cars. :). but i want to get to the 12k barrier. i have ordered my N1 block allready, till that arrives early next year ill have the head built in california and the special sump ordered, then it comes time for the step 3 stroker. when ill be building the setup ill keep you guys posted with pics, as early next year ill have a 8k internet connection so i can psot up a lot of pics. now i am running a crappy 64kb internet connection (stupid 3rd world country)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...